Mecklenburg XIX
Mecklenburg T7
Type and origin
BuilderKrauss
Build date1891, 1898
Total produced2
Specifications
Configuration:
  Whyte0-6-0T
Gauge900 mm (2 ft 11+716 in)
Coupled dia.700 mm (2 ft 3+12 in)
Wheelbase:
  Overall1,800 mm (5 ft 10+34 in)
Length:
  Over beams5,530 mm (18 ft 1+34 in)
Height3,705 mm (12 ft 1+78 in)
Axle load5.33 t (5.25 long tons; 5.88 short tons)
Adhesive weight15.98 t (15.73 long tons; 17.61 short tons)
Empty weight13.08 t (12.87 long tons; 14.42 short tons)
Service weight15.98 t (15.73 long tons; 17.61 short tons)
Fuel capacity750 kg (1,650 lb)
Water cap.1.70 m3 (370 imp gal; 450 US gal)
Boiler:
No. of heating tubes88
Heating tube length2,200 mm (7 ft 2+12 in)
Boiler pressure12 kgf/cm2 (1,180 kPa; 171 lbf/in2)
Heating surface:
  Tubes26.76 m2 (288.0 sq ft)
  Firebox0.43 m2 (4.6 sq ft)
  Radiative2.17 m2 (23.4 sq ft)
  Evaporative28.93 m2 (311.4 sq ft)
Cylinders2
Cylinder size260 mm (10+14 in)
Piston stroke400 mm (15+34 in)
Performance figures
Maximum speed31 km/h (19 mph)
Career
NumbersMFFE: 1003 and 1004
Retired1923, 1924

The locomotives of Class XIX of the Grand Duchy of Mecklenburg Friedrich-Franz Railway were deployed on the Bad Doberan–Heiligendamm narrow-gauge. The triple-coupled engines were classified as T 7 locomotives in 1910. In 1911 they were transferred to the Neubukow Beet Railway.

History

The Class XVIII locomotives were soon unable to cope with the increase in traffic. As a result, a triple-coupled engine was ordered from Krauss in Munich. The locomotive was given the number 1003 by the Mecklenburg State Railway and was incorporated into Class XIX. In 1898 another locomotive, number 1004, followed. In 1910 the line was extended as far as Arendsee. To handle the higher levels of traffic, three similar engines were ordered from Henschel. With the introduction into service of these locomotives, that were grouped into Class T 7, the two Krauss locomotives were given to the Neubukow Beet Railway. The engines were still listed in the first Deutsche Reichsbahn renumbering plan in 1923, but they were retired by 1924.

Design features

The locomotives had an inside frame which was built as a water tank. The boiler comprised two shell rings. The steam dome with its safety valve sat on the forward shell ring. The smokebox was very short. The smokestack has a Kobel spark arrestor. Later a Prüsmann chimney was used.

The horizontally arranged two-cylinder, wet steam drive acted on the rearmost coupled axle. The Stephenson valve gear with crossed eccentric rods was also on the outside.

The two front coupled axles had leaf spring blocks at the height of the running plate. These were linked by equalising beams. The rear axle was sprung with a transverse leaf spring stack.

The hand brake acted on the two outside wheel sets from the outside. Later the locomotives were given Knorr air brakes. The sanding gear sat on the middle of the boiler and sanded the outer sets of wheels from the outside. To begin with the running gear was covered. The locomotives also had steam heating, a steam bell and a De Limon centralized lubricating system.

References

  • Kirsche, Hans-Joachim; Lohr, Hermann; Thielmann, Georg (1989). Lokomotiv-Archiv Mecklenburg/Oldenburg. Berlin: transpress. ISBN 3-344-00326-7.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.