Historical

FAT was also used on hard disks throughout the DOS and Windows 9x eras. Microsoft introduced NTFS with the Windows NT platform in 1993, but FAT remained the standard for the home user until the introduction of Windows XP in 2001. Windows Me was the final version of Windows to use FAT as its default file system.

For floppy disks, FAT has been standardized as ECMA-107^[6] and ISO/IEC 9293:1994^[7] (superseding ISO 9293:1987^[8]). These standards cover FAT12 and FAT16 with only short 8.3 filename support; long filenames with VFAT were partially patented.^[9] While FAT12 is used on floppy disks, FAT16 and FAT32 are typically found on the larger media.

Modern

FAT is used internally for the EFI system partition in the boot stage of EFI-compliant computers.^[10] Hidden FAT filesystems are also used in the UEFI boot partition on modern PCs.

FAT is still used in drives expected to be used by multiple operating systems, such as in shared Windows, Linux and DOS environments. Microsoft Windows additionally comes with a pre-installed tool to convert a FAT file system into NTFS directly without the need to rewrite all files, though this cannot be reversed easily.^[11] The FAT file system is used in removable media such as floppy disks, super-floppies, memory and flash memory cards or USB flash drives. FAT is supported by portable devices such as PDAs, digital cameras, camcorders, media players, and mobile phones.^[3]

The DCF file system adopted by almost all digital cameras since 1998 defines a logical file system with 8.3 filenames and makes the use of either FAT12, FAT16, FAT32 or exFAT mandatory for its physical layer for compatibility.^[12]

Original 8-bit FAT

The original FAT file system (or FAT structure, as it was called initially) was designed and implemented by Marc McDonald,^[15] based on a series of discussions between McDonald and Bill Gates.^[15] It was introduced with 8-bit table elements^[13][14][15] (and valid data cluster numbers up to 0xBF^[13][14]) in a precursor to Microsoft's Standalone Disk BASIC-80 for an 8080-based successor^{[nb 2]} of the NCR 7200 model VI data-entry terminal, equipped with 8-inch (200 mm) floppy disks, in 1977^[16] or 1978.^{[nb 2]} In 1978, Standalone Disk BASIC-80 was ported to the 8086 using an emulator on a DEC PDP-10,^[17] since no real 8086 systems were available at this time. The FAT file system was also used in Microsoft's MDOS/MIDAS,^[15] an operating system for 8080/Z80 platforms written by McDonald since 1979. The Standalone Disk BASIC version supported three FATs,^[13][14][18] whereas this was a parameter for MIDAS. Reportedly, MIDAS was also prepared to support 10-bit, 12-bit and 16-bit FAT variants. While the size of directory entries was 16 bytes in Standalone Disk BASIC,^[13][14] MIDAS instead occupied 32 bytes per entry.

Tim Paterson of Seattle Computer Products (SCP) was first introduced to Microsoft's FAT structure when he helped Bob O'Rear adapting the Standalone Disk BASIC-86 emulator port onto SCP's S-100 bus 8086 CPU board prototype during a guest week at Microsoft in May 1979.^[17] The final product was shown at Lifeboat Associates' booth stand at the National Computer Conference in New York^[17] on June 4–7, 1979, where Paterson learned about the more sophisticated FAT implementation in MDOS/MIDAS^[15] and McDonald talked to him about the design of the file system.^[16]

FAT12

Between April and August 1980, while borrowing the FAT concept for SCP's own 8086 operating system QDOS 0.10,^[17] Tim Paterson extended the table elements to 12 bits,^[19] reduced the number of FATs to two, redefined the semantics of some of the reserved cluster values, and modified the disk layout, so that the root directory was now located between the FAT and the data area for his implementation of FAT12. Paterson also increased the nine-character (6.3) filename^[13][14] length limit to eleven characters to support CP/M-style 8.3 filenames and File Control Blocks. The format used in Microsoft Standalone Disk BASIC's 8-bit file system precursor was not supported by QDOS. By August 1980, QDOS had been renamed 86-DOS.^[20] Starting with 86-DOS 0.42, the size and layout of directory entries was changed from 16 bytes to 32 bytes^[21] in order to add a file date stamp^[21] and increase the theoretical file size limit beyond the previous limit of 16 MB.^[21] 86-DOS 1.00 became available in early 1981. Later in 1981, 86-DOS evolved into Microsoft's MS-DOS and IBM PC DOS.^[15][19][22] The capability to read previously formatted volumes with 16-byte directory entries^[21] was dropped with MS-DOS 1.20.

FAT12 used 12-bit entries for the cluster addresses; some values were reserved to mark the end of a chain of clusters, to mark unusable areas of the disk, or for other purposes, so the maximum number of clusters was limited to 4078.^[23][24] To conserve disk space, two 12-bit FAT entries used three consecutive 8-bit bytes on disk, requiring manipulation to unpack the 12-bit values. This was sufficient for the original floppy disk drives, and small hard disks up to 32 megabytes. The FAT16B version available with DOS 3.31 supported 32-bit sector numbers, and so increased the volume size limit.

All the control structures fit inside the first track, to avoid head movement during read and write operations. Any bad sector in the control structures area would make the disk unusable. The DOS formatting tool rejected such disks completely. Bad sectors were allowed only in the file data area. Clusters containing bad sectors were marked unusable with the reserved value 0xFF7 in the FAT.

While 86-DOS supported three disk formats (250.25 KB, 616 KB and 1232 KB, with FAT IDs 0xFF and 0xFE) on 8-inch (200 mm) floppy drives, IBM PC DOS 1.0, released with the original IBM Personal Computer in 1981, supported only an 8-sector floppy format with a formatted capacity of 160 KB (FAT ID 0xFE) for single-sided 5.25-inch floppy drives, and PC DOS 1.1 added support for a double-sided format with 320 KB (FAT ID 0xFF). PC DOS 2.0 introduced support for 9-sector floppy formats with 180 KB (FAT ID 0xFC) and 360 KB (FAT ID 0xFD).

86-DOS 1.00 and PC DOS 1.0 directory entries included only one date, the last modified date. PC DOS 1.1 added the last modified time. PC DOS 1.x file attributes included a hidden bit and system bit, with the remaining six bits undefined. At this time, DOS did not support sub-directories, but typically there were only a few dozen files on a diskette.

The PC XT was the first PC with an IBM-supplied hard drive, and PC DOS 2.0 supported that hard drive with FAT12 (FAT ID 0xF8). The fixed assumption of 8 sectors per clusters on hard disks practically limited the maximum partition size to 16 MB for 512 byte sectors and 4 KB clusters.

The BIOS Parameter Block (BPB) was introduced with PC DOS 2.0 as well, and this version also added read-only, archive, volume label, and directory attribute bits for hierarchical sub-directories.^[25]

MS-DOS 3.0 introduced support for high-density 1.2 MB 5.25-inch diskettes (media descriptor 0xF9), which notably had 15 sectors per track, hence more space for the FATs.

FAT12 remains in use on all common floppy disks, including 1.44 MB and later 2.88 MB disks (media descriptor byte 0xF0).

Initial FAT16

In 1984, IBM released the PC AT, which required PC DOS 3.0 to access its 20 MB hard disk.^[26][27] Microsoft introduced MS-DOS 3.0 in parallel. Cluster addresses were increased to 16-bit, allowing for up to 65,526 clusters per volume. However, the maximum possible number of sectors and the maximum partition size of 32 MB did not change. Although cluster addresses were 16 bits, this format was not what today is commonly understood as FAT16. A partition type 0x04 indicates this form of FAT16 with less than 65,536 sectors (less than 32 MB for sector size 512). The benefit of FAT16 was the use of smaller clusters, making disk usage more efficient, particularly for large numbers of files only a few hundred bytes in size.

As MS-DOS 3.0 formatted all 16 MB-32 MB partitions in the FAT16 format, a 20 MB hard disk formatted under MS-DOS 3.0 was not accessible by MS-DOS 2.0.^[28] MS-DOS 3.0 to MS-DOS 3.30 could still access FAT12 partitions under 15 MB, but required all 16 MB-32 MB partitions to be FAT16, and so could not access MS-DOS 2.0 partitions in this size range. MS-DOS 3.31 and higher could access 16 MB-32 MB FAT12 partitions again.

Logical sectored FAT

MS-DOS and PC DOS implementations of FAT12 and FAT16 could not access disk partitions larger than 32 megabytes. Several manufacturers developed their own FAT variants within their OEM versions of MS-DOS.^[29]

Some vendors (AST and NEC^[29]) supported eight, instead of the standard four, primary partition entries in their custom extended Master Boot Record (MBR), and they adapted MS-DOS to use more than a single primary partition.

Other vendors worked around the volume size limits imposed by the 16-bit sector entries by increasing the apparent size of the sectors the file system operated on. These logical sectors were larger (up to 8192 bytes) than the physical sector size (still 512 bytes) on the disk. The DOS-BIOS or System BIOS would then combine multiple physical sectors into logical sectors for the file system to work with.

These changes were transparent to the file system implementation in the DOS kernel. The underlying DOS-BIOS translated these logical sectors into physical sectors according to partitioning information and the drive's physical geometry.

The drawback of this approach was increased memory used for sector buffering and deblocking. Since older DOS versions could not use large logical sectors, the OEMs introduced new partition IDs for their FAT variants in order to hide them from off-the-shelf issues of MS-DOS and PC DOS. Known partition IDs for logical sectored FATs include: 0x08 (Commodore MS-DOS 3.x), 0x11 (Leading Edge MS-DOS 3.x), 0x14 (AST MS-DOS 3.x), 0x24 (NEC MS-DOS 3.30^[29]), 0x56 (AT&T MS-DOS 3.x), 0xE5 (Tandy MS-DOS), 0xF2 (Sperry IT MS-DOS 3.x, Unisys MS-DOS 3.3 – also used by Digital Research DOS Plus 2.1).^[30] OEM versions like Toshiba MS-DOS, Wyse MS-DOS 3.2 and 3.3,^[31] as well as Zenith MS-DOS are also known to have utilized logical sectoring.^[32]

While non-standard and sub-optimal, these FAT variants are perfectly valid according to the specifications of the file system itself. Therefore, even if default issues of MS-DOS and PC DOS were not able to cope with them, most of these vendor-specific FAT12 and FAT16 variants can be mounted by more flexible file system implementations in operating systems such as DR-DOS, simply by changing the partition ID to one of the recognized types.^{[nb 3]} Also, if they no longer need to be recognized by their original operating systems, existing partitions can be "converted" into FAT12 and FAT16 volumes more compliant with versions of MS-DOS/PC DOS 4.0–6.3, which do not support sector sizes different from 512 bytes,^[33] by switching to a BPB with 32-bit entry for the number of sectors, as introduced since DOS 3.31 (see FAT16B below), keeping the cluster size and reducing the logical sector size in the BPB down to 512 bytes, while at the same time increasing the counts of logical sectors per cluster, reserved logical sectors, total logical sectors, and logical sectors per FAT by the same factor.

A parallel development in MS-DOS / PC DOS which allowed an increase in the maximum possible FAT size was the introduction of multiple FAT partitions on a hard disk. To allow the use of more FAT partitions in a compatible way, a new partition type was introduced in PC DOS 3.2 (1986), the extended partition (EBR),^[15] which is a container for an additional partition called logical drive. Since PC DOS 3.3 (April 1987), there is another, optional extended partition containing the next logical drive, and so on. The MBR of a hard disk can either define up to four primary partitions, or an extended partition in addition to up to three primary partitions.

Final FAT16

In November 1987, Compaq Personal Computer DOS 3.31 (a modified OEM version of MS-DOS 3.3 released by Compaq with their machines) introduced what today is simply known as the FAT16 format, with the expansion of the 16-bit disk sector count to 32 bits in the BPB. Although the on-disk changes were minor, the entire DOS disk driver had to be converted to use 32-bit sector numbers, a task complicated by the fact that it was written in 16-bit assembly language. The result was initially called the DOS 3.31 Large File System. Microsoft's DSKPROBE tool refers to type 0x06 as BigFAT,^[35] whereas some older versions of FDISK described it as BIGDOS. Technically, it is known as FAT16B.

Since older versions of DOS were not designed to cope with more than 65,535 sectors, it was necessary to introduce a new partition type for this format in order to hide it from pre-3.31 issues of DOS. The original form of FAT16 (with less than 65,536 sectors) had a partition type 0x04. To deal with disks larger than this, type 0x06 was introduced to indicate 65,536 or more sectors. In addition to this, the disk driver was expanded to cope with more than 65,535 sectors as well. The only other difference between the original FAT16 and the newer FAT16B format is the usage of a newer BPB format with 32-bit sector entry. Therefore, newer operating systems supporting the FAT16B format can cope also with the original FAT16 format without any necessary changes.

If partitions to be used by pre-DOS 3.31 issues of DOS need to be created by modern tools, the only criteria theoretically necessary to meet are a sector count of less than 65536, and the usage of the old partition ID (0x04). In practice however, type 0x01 and 0x04 primary partitions should not be physically located outside the first 32 MB of the disk, due to other restrictions in MS-DOS 2.x, which could not cope with them otherwise.

In 1988, the FAT16B improvement became more generally available through DR DOS 3.31, PC DOS 4.0, OS/2 1.1, and MS-DOS 4.0. The limit on partition size was dictated by the 8-bit signed count of sectors per cluster, which originally had a maximum power-of-two value of 64. With the standard hard disk sector size of 512 bytes, this gives a maximum of 32 KB cluster size, thereby fixing the "definitive" limit for the FAT16 partition size at 2 GB for sector size 512. On magneto-optical media, which can have 1 or 2 KB sectors instead of 0.5 KB, this size limit is proportionally larger.

Much later, Windows NT increased the maximum cluster size to 64 KB, by considering the sectors-per-cluster count as unsigned. However, the resulting format was not compatible with any other FAT implementation of the time, and it generated greater internal fragmentation. Windows 98, SE and ME also supported reading and writing this variant, but its disk utilities did not work with it and some FCB services are not available for such volumes. This contributes to a confusing compatibility situation.

Prior to 1995, versions of DOS accessed the disk via CHS addressing only. When Windows 95(MS-DOS 7.0) introduced LBA disk access, partitions could start being physically located outside the first c. 8 GB of this disk and thereby out of the reach of the traditional CHS addressing scheme. Partitions partially or fully located beyond the CHS barrier therefore had to be hidden from non-LBA-enabled operating systems by using the new partition type 0x0E in the partition table instead. FAT16 partitions using this partition type are also named FAT16X.^[36] The only difference, compared to previous FAT16 partitions, is the fact that some CHS-related geometry entries in the BPB record, namely the number of sectors per track and the number of heads, may contain no or misleading values and should not be used.

The number of root directory entries available for FAT12 and FAT16 is determined when the volume is formatted, and is stored in a 16-bit field. For a given number RDE and sector size SS, the number RDS of root directory sectors is RDS = ceil((RDE × 32) / SS), and RDE is normally chosen to fill these sectors, i.e., RDE × 32 = RDS × SS. FAT12 and FAT16 media typically use 512 root directory entries on non-floppy media. Some third-party tools, like mkdosfs, allow the user to set this parameter.^[37]

FAT32

In order to overcome the volume size limit of FAT16, while at the same time allowing DOS real-mode code to handle the format, Microsoft designed a new version of the file system, FAT32, which supported an increased number of possible clusters, but could reuse most of the existing code, so that the conventional memory footprint was increased by less than 5 KB under DOS.^[38] Cluster values are represented by 32-bit numbers, of which 28 bits are used to hold the cluster number.

Extended attributes

OS/2 heavily depends on extended attributes (EAs) and stores them in a hidden file called "EA␠DATA.␠SF" in the root directory of the FAT12 or FAT16 volume. This file is indexed by two previously reserved bytes in the file's (or directory's) directory entry at offset 0x14.^[51] In the FAT32 format, these bytes hold the upper 16 bits of the starting cluster number of the file or directory, hence making it impossible to store OS/2 EAs on FAT32 using this method.

However, the third-party FAT32 installable file system (IFS) driver FAT32.IFS version 0.70 and higher by Henk Kelder & Netlabs for OS/2, eComStation and ArcaOS stores extended attributes in extra files with filenames having the string "␠EA.␠SF" appended to the regular filename of the file to which they belong. The driver also utilizes the byte at offset 0x0C in directory entries to store a special mark byte indicating the presence of extended attributes to help speed up things.^[52][53] (This extension is critically incompatible with the FAT32+ method to store files larger than 4 GB minus 1 on FAT32 volumes.)^[34]

Extended attributes are accessible via the Workplace Shell desktop, through REXX scripts, and many system GUI and command-line utilities (such as 4OS2).^[54]

To accommodate its OS/2 subsystem, Windows NT supports the handling of extended attributes in HPFS, NTFS, FAT12 and FAT16. It stores EAs on FAT12, FAT16 and HPFS using exactly the same scheme as OS/2, but does not support any other kind of ADS as held on NTFS volumes. Trying to copy a file with any ADS other than EAs from an NTFS volume to a FAT or HPFS volume gives a warning message with the names of the ADSs that will be lost. It does not support the FAT32.IFS method to store EAs on FAT32 volumes.

Windows 2000 onward acts exactly as Windows NT, except that it ignores EAs when copying to FAT32 without any warning (but shows the warning for other ADSs, like "Macintosh Finder Info" and "Macintosh Resource Fork").

Cygwin uses "EA␠DATA.␠SF" files as well.

Long file names

One of the user experience goals for the designers of Windows 95 was the ability to use long filenames (LFNs—up to 255 UTF-16 code units long),^{[nb 1]} in addition to classic 8.3 filenames (SFNs). For backward and forward compatibility, LFNs were implemented as an optional extension on top of the existing FAT file system structures using a workaround in the way directory entries are laid out.

This transparent method to store long file names in the existing FAT file systems without altering their data structures is usually known as VFAT (for "Virtual FAT") after the Windows 95 virtual device driver.^{[nb 5]}

Non VFAT-enabled operating systems can still access the files under their short file name alias without restrictions; however, the associated long file names may be lost when files with long filenames are copied under non VFAT-aware operating systems.

In Windows NT, support for VFAT long filenames began with version 3.5.

Linux provides a VFAT filesystem driver to work with FAT volumes with VFAT long filenames. For some time, a UVFAT driver was available to provide combined support for UMSDOS-style permissions with VFAT long filenames.

OS/2 added long filename support to FAT using extended attributes (EA) before the introduction of VFAT. Thus, VFAT long filenames are invisible to OS/2, and EA long filenames are invisible to Windows; therefore, experienced users of both operating systems would have to manually rename the files.

Human68K supported up to 18.3 filenames and (Shift JIS) Kanji characters in a proprietary FAT file system variant.

In order to support Java applications, the FlexOS-based IBM 4690 OS version 2 introduced its own virtual file system (VFS) architecture to store long filenames in the FAT file system in a backwards-compatible fashion. If enabled, the virtual filenames (VFN) are available under separate logical drive letters, whereas the real filenames (RFN) remain available under the original drive letters.^[55]

Forks and alternate data streams

The FAT file system itself is not designed for supporting alternate data streams (ADS), but some operating systems that heavily depend on them have devised various methods for handling them on FAT volumes. Such methods either store the additional information in extra files and directories (classic Mac OS and macOS), or give new semantics to previously unused fields of the FAT on-disk data structures (OS/2 and Windows NT).

Mac OS using PC Exchange stores its various dates, file attributes and long filenames in a hidden file called "FINDER.DAT", and resource forks (a common Mac OS ADS) in a subdirectory called "RESOURCE.FRK", in every directory where they are used. From PC Exchange 2.1 onwards, they store the Mac OS long filenames as standard FAT long filenames and convert FAT filenames longer than 31 characters to unique 31-character filenames, which can then be made visible to Macintosh applications.

macOS stores resource forks and metadata (file attributes, other ADS) using AppleDouble format in a hidden file with a name constructed from the owner filename prefixed with "._", and Finder stores some folder and file metadata in a hidden file called ".DS_Store" (but note that Finder uses .DS_Store even on macOS' native filesystem, HFS+).

UMSDOS permissions and filenames

Early Linux distributions also supported a format known as UMSDOS, a FAT variant with Unix file attributes (such as long file name and access permissions) stored in a separate file called "--linux-.---". UMSDOS fell into disuse after VFAT was released and it is not enabled by default in Linux from version 2.5.7 onwards.^[56] For some time, Linux also provided combined support for UMSDOS-style permissions and VFAT long filenames through UVFAT.

FAT+

In 2007 the open FAT+ draft proposed how to store larger files up to 256 GB minus 1 byte, or 274,877,906,943 (2³⁸ − 1) bytes, on slightly modified and otherwise backward-compatible FAT32 volumes,^[34] but imposes a risk that disk tools or FAT32 implementations not aware of this extension may truncate or delete files exceeding the normal FAT32 file size limit. Support for FAT32+ and FAT16+ is limited to some versions of DR-DOS and not available in mainstream operating systems.^[57] (This extension is critically incompatible with the /EAS option of the FAT32.IFS method to store OS/2 extended attributes on FAT32 volumes.)

Turbo FAT

In its NetWare File System (NWFS) Novell implemented a heavily modified variant of a FAT file system for the NetWare operating system. For larger files it utilized a performance feature named Turbo FAT.

FATX

FATX is a family of file systems designed for Microsoft's Xbox video game console hard disk drives and memory cards,^[58][59] introduced in 2001.

While resembling the same basic design ideas as FAT16 and FAT32, the FATX16 and FATX32 on-disk structures are simplified, but fundamentally incompatible with normal FAT16 and FAT32 file systems, making it impossible for normal FAT file system drivers to mount such volumes.

The non-bootable superblock sector is 4 KB in size and holds an 18 byte large BPB-like structure completely different from normal BPBs. Clusters are typically 16 KB in size and there is only one copy of the FAT on the Xbox. Directory entries are 64 bytes in size instead of the normal 32 bytes. Files can have filenames up to 42 characters long using the OEM character set and be up to 4 GB minus 1 byte in size. The on-disk timestamps hold creation, modification and access dates and times but differ from FAT: in FAT, the epoch is 1980; in FATX, the epoch is 2000. On the Xbox 360, the epoch is 1980.^[60]

exFAT

exFAT is a file system introduced with Windows Embedded CE 6.0 in November 2006 and brought to the Windows NT family with Vista Service Pack 1 and Windows XP Service Pack 3 (or separate installation of Windows XP Update KB955704). It is loosely based on the File Allocation Table architecture, but incompatible, proprietary and protected by patents.^[61]

exFAT is intended for use on flash drives and memory cards such as SDXC and Memory Stick XC, where FAT32 is otherwise used. Vendors usually pre-format SDXC cards with it. Its main benefit is its exceeding of the 4 GB file size limit, as file size references are stored with eight instead of four bytes, increasing the limit to 2⁶⁴ − 1 bytes.

Microsoft's GUI and command-line format utilities offer it as an alternative to NTFS (and, for smaller partitions, to FAT16B and FAT32). The MBR partition type is 0x07 (the same as used for IFS, HPFS, and NTFS). Logical geometry information located in the VBR is stored in a format not resembling any kind of BPB.

In early 2010, the file system was reverse-engineered by the SANS Institute.^[62] On August 28, 2019, Microsoft published the technical specification for exFAT so that it can be used in the Linux kernel and other operating systems.^[63]

Challenges and lawsuits

The Public Patent Foundation (PUBPAT) submitted evidence to the US Patent and Trademark Office (USPTO) in 2004 disputing the validity of U.S. patent 5579517,^[64] including prior art references from Xerox and IBM.^[72] The USPTO opened an investigation and concluded by rejecting all claims in the patent.^[73] The next year, the USPTO further announced that following the re-examination process, it affirmed the rejection of '517 and additionally found U.S. patent 5,758,352^[66] invalid on the grounds that the patent had incorrect assignees.

However, in 2006, the USPTO ruled that features of Microsoft's implementation of the FAT system were "novel and non-obvious", reversing both earlier decisions and leaving the patents valid.^[74]

In February 2009, Microsoft filed a patent infringement lawsuit against TomTom alleging that the device maker's products infringe on patents related to VFAT long filenames. As some TomTom products are based on Linux, this marked the first time that Microsoft tried to enforce its patents against the Linux platform.^[75] The lawsuit was settled out of court the following month with an agreement that Microsoft be given access to four of TomTom's patents, that TomTom will drop support for the VFAT long filenames from its products, and that in return Microsoft not seek legal action against TomTom for the five-year duration of the settlement agreement.^[76]

In October 2010, Microsoft filed a patent infringement lawsuit against Motorola alleging several patents (including two of the VFAT patents) were not licensed for use in the Android operating system.^[77] They also submitted a complaint to the ITC.^[78] Developers of open source software have designed methods intended to circumvent Microsoft's patents.^[79][80]

In 2013, patent EP0618540 "common name space for long and short filenames" (expired since 2014^[81]) was invalidated in Germany.^[82] After the appeal was withdrawn, this judgment became final on the 28th October 2015.^[83]