Teddy Ruxpin Eyes Replacement

Written By: Jayin Patel
  • Comments: 3
Teddy Ruxpin Eyes Replacement

Difficulty

Difficult

Steps

13

Time Required

1 hour

Introduction

Teddy Ruxpin’s eyes are LED and will react to story-time. If the eyes are glitching, not turning on, or malfunctioning in any way, follow this guide to replace them. Be cautious during desoldering and keep track of screws. Refer to the desoldering guide for help.

  1. nUfqWgdYJtTKYxX2
    nUfqWgdYJtTKYxX2
    MTMSkcBDOVfbFRo5

    • Remove the vest covering the back of the bear.

    • Orient the bear with his back facing upwards and unscrew the single Phillips #2 screw.

    • Captured screws will stay in place, no need to worry about losing this one!

    If screw is missing could this be the problem

    nursejackie55 -

  2. rcVNXibq5Wd4hyBF

    • Pull the tab outward to remove the protective plate for the batteries.

  3. V4C2rIHN1X5vcVeV

    • Remove all four AA batteries by pushing the positive end down and pulling the battery out toward yourself.

    I have already changed out the batteries and it still want com on.

    Wendy Nickel

    breezy_bear99 -

  4. PfvEn1FycGsIjPi3
    PfvEn1FycGsIjPi3
    AxRppx1A3ogsHHdx
    TGQLCcuxCwYpsK6G

    • Cut the orange shirt and zip tie.

    • Remove the zip tie.

  5. fRltQEldCiKbE4SW

    • Cut across the back seam of the head of the bear along the arrow.

    • This damages the bear's exterior and will require resewing.

  6. sttQCmwI5NEMlVNH
    sttQCmwI5NEMlVNH
    2DOaIMHR2RN1bSJp
    nIWti1jICOHWt3m4

    • Remove the interior of the doll.

    • Peel the outer layer around the head of the bear and forcefully pry off the face of the bear from the outside layer of the bear.

    • This will be difficult and require significant force, but do not fear about breaking the doll at this stage.

  7. 5J1YnN1BcoXKp6IE
    5J1YnN1BcoXKp6IE
    6bntgI1X2mt3j5Tk

    • Extract each arm button.

    • Pull on the stuffing of the bear and not the wire to remove the arm button.

  8. MFc6lIh56jrjlddT
    MFc6lIh56jrjlddT
    ixHPOAqaLFaJnTv4

    • Pull off the rest of the outside layer of the bear.

  9. LV56yunOSYVWKnBA

    • Unplug the arms from the main body.

  10. BuuDpcPQBmWlWmD3
    BuuDpcPQBmWlWmD3
    WLeOVhVoSWCbgG44
    uouWsiNupK6N5Iib

    • Unscrew the eleven circled 12.5mm Phillips #1 screws.

    • Remove the top of the housing to access the electronics inside.

  11. foR6c5oZRXHmKfxv

    • Using a Phillips #1 screwdriver, remove the two 12.5mm screws connecting the eyes to the rest of the mechanism.

  12. wRENSEjXr1AW6qpv
    wRENSEjXr1AW6qpv
    xFEISWqKvcT1MYgh

    • Unplug the two sets of wires connected to the back of the eyes by using moderate to high force.

  13. waHnOCHoLSSaQRPD

    • Once those wires are disconnected, desolder the wires connected from the eye motherboard.

    Did you forget his LCD eyes

    James Bonnick -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jayin Patel

Member since: 23/01/20

406 Reputation

0 comments