Repair Broken Connections in the Pyrus PY21S03211

Written By: Danielle Hadaway
  • Comments: 0
Repair Broken Connections in the Pyrus PY21S03211

Difficulty

Moderate

Steps

15

Time Required

30 minutes

Introduction

This guide is designed to help solder any wires that may be broken. Soldering irons are somewhat dangerous to handle due to the extreme heat, so exercise caution when soldering. It's also very important to keep the thick white connector from breaking, so when opening the side panel, keep the device close to the panel until the connector is safely removed.

  1. hUJBVyjh5ONcxQpL

    • Turn the video camera upside down so the bottom of the device is visible.

  2. yWlcDOxOnW1afBHa
    yWlcDOxOnW1afBHa
    QoqbG2r6hgkFCwKk

    • Pull back the bottom tab to reveal the battery compartment.

  3. wFnTLxXr4reueVAM

    • Pull back the tab that is holding in the battery in place and remove the battery from the device.

  4. UfyLcsZHaQK6pehw

    • Find the device's HDMI/TV cover.

  5. KBBa5ZFZULxNVwqu

    • Open the cover to reveal the device ports.

  6. jDsgZH2B32BuTXGH
    jDsgZH2B32BuTXGH
    RFMTOGia1wJeMjKe

    • Use the screwdriver to remove the 2 4mm screws from the port cover.

  7. gQHqcEME1unCL2qd
    gQHqcEME1unCL2qd
    RyDHMmkApnndjbvK
    axBP2l3KI2rOytld

    • Use the tweezers to remove the plastic port cover.

  8. YYF2VaeXZ66QQyHK

    • Open the display screen.

  9. iSwqIpLnMkeWj3Wl
    iSwqIpLnMkeWj3Wl
    YjbFYYiiSNLBirv6
    1CkgXnqOWdmfIUEE

    • Use tweezers to carefully pull out the circular stickers to reveal the 4mm screws.

  10. WTDCIwEIPiVpYHiB
    WTDCIwEIPiVpYHiB
    PfROj3HQ4TmknR4N

    • Use the screwdriver to remove all six 4mm screws from the side of the device.

  11. SFldLkTkVaNDiYTv
    SFldLkTkVaNDiYTv
    hSENcyastMxy3Sas
    Xhu6f6nCpKDQXTMC

    • Use a thin plastic pick to pry off the side of the device and carefully remove the display.

  12. XB6pIV3m26BXruLF

    • Carefully remove the side face from the device. Avoid pulling on the white connector.

  13. mkNFqniHsGO3qV2y

    • To remove the side face entirely, find the large white connector, flip open the grey lip with tweezers, and gently remove the white connector.

  14. lRHlDCnFIswFcgEi

    • Find the broken wire.

  15. kVhlSt4CUcogUaWu
    kVhlSt4CUcogUaWu
    LgWCVj341RVLyZcH
    1rE31OdSlmmIq1Hv

Author

Danielle Hadaway

Member since: 31/03/16

255 Reputation

0 comments