Nobis NB07 Cameras Replacement

Written By: Daniel Gomero
  • Comments: 0
Nobis NB07 Cameras Replacement

Difficulty

Moderate

Steps

9

Time Required

15 - 20 minutes

Introduction

Is one or both of your tablet's cameras broken? You can use this guide to replace it. Following these steps, you will disassemble your tablet and replace the faulty camera.

  1. rFi2fqDxS6EjjHxY

    • Look towards the topside of the tablet, where the power button is located.

    • Insert a plastic opening tool in the crack between the two parts of the case.

    • Move it gently back and forth to open the case.

  2. nVx4VHobZE1FksaY
    nVx4VHobZE1FksaY
    yKBkMhDlMFOqWDAX
    eNJHZkGXvvGXPYnG

    • With the plastic opening tool in the opening between the two sides of the case, slide the tool along the tablet's border to separate the two sides completely.

    • Be careful when you separate the two halves. Open the case from the opposite side of the camera, there is a cable connecting both halves of the case.

  3. lovyBpP4PBuveIDL
    lovyBpP4PBuveIDL
    dHapKFTKUSZofwow
    1pXBmRrSrULpFaqI

    • Remove the tape holding the battery in place.

  4. IRNF3H6vc5tAjnkl
    IRNF3H6vc5tAjnkl
    aLKyTAtmDbaZX2HO
    gJL2awI5osS3VhrD

    • Insert the flat end of the spudger tool in the crack beneath the battery.

    • Move the spudger tool carefully side to side to remove the glue that is holding the battery in place.

    • This is a soft battery, so a little bending is expected.

  5. 4IvCeQxsfXZdg3oP

    • After the battery is unglued, locate the cables that connect it to the motherboard.

    • Annotate where each color goes to make the reassembly easier.

  6. eJQSeBLYFthaYwAL
    eJQSeBLYFthaYwAL
    lTq22X6fjugU1oDL

    • Desolder the cables with a soldering iron and use a desoldering braid to remove the solder.

    • Review the Ifixit soldering guide if you need help soldering.

    • You can now remove the battery.

  7. PLORxGrZUo542M3x
    PLORxGrZUo542M3x
    YMrM1FANniDBMclW
    D4YFiPqOFHFq1fLw

    • Remove the black tape covering the cameras power cable.

  8. kHBQpIyUACaLc5rH
    kHBQpIyUACaLc5rH
    C1nLI1a3ksSBDaqK

    • Use the spudger tool to pry upwards the ZIF connector and release the power cable.

  9. RmVGAW5iXxKOlWYA
    RmVGAW5iXxKOlWYA
    HuvUPC3JNhFp6AT1
    4OLOqvp2AxusSBMe

    • With the power cable disconnected, the backside camera is free. However, both cameras are sequentially connected through the power cable; the front side camera is glued to the motherboard.

    • Using tweezers, carefully grab the front camera and twist slowly.

    • The camera should release easily, do not twist too hard.

    • You can now remove the cameras.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Daniel Gomero

Member since: 21/01/15

966 Reputation

0 comments