Jawbone Big Jambox Speaker Replacement

Written By: Taryn Kelley
  • Comments: 28
Jawbone Big Jambox Speaker Replacement

Difficulty

Moderate

Steps

10

Time Required

30 - 45 minutes

Introduction

If your speaker is not working, it may need to be replaced. This guide requires having a new, compatible speaker to replace the broken one with.

  1. FbdZmkEPUobQUF52

    • Remove both end caps by putting a plastic opening tool in the center of the seam. Work around the edges to pry the end caps off completely.

    • Due to interior clips holding the end caps in place, use caution when applying force.

    Can someone show the clips please in a photo?

    kenneth keen -

  2. gpR1qeYVfuiKrJPf
    gpR1qeYVfuiKrJPf
    4Xapn3AX3HIZYmBZ
    htYRDmTSEfZLbJMj

    • Turn the Jambox upside down. Peel the indicated rubber tabs off, using a plastic opening tool if necessary.

    • You may want to only take the tabs half way off to avoid re-gluing when reassembling.

    • Remove the three T6, 7.0 mm screws under each rubber tab.

    • Because the screws are a different length, set the screws aside.

    I used rubber cement to reattach the pads. That will hold them in place and be easily removable in future.

    David Robinson -

    Can someone show a picture of the screws…and where they screw not…even just for form’s sake?

    Thousand Sunny -

  3. GVMKQYqV4vHagsML
    GVMKQYqV4vHagsML
    mxDNbPDkIpXGSfS5
    ZcDVcDPp2jorIIPE

    • With the Jawbone logo facing towards you and with correct orientation, place the Jambox with the left end cap facing upward.

    • Unscrew indicated T6 9.7 mm screws.

    • Gently loosen the tabs from their anchor points so the bottom may be removed.

    • Flip the Jambox so the other end cap is facing up. The USB cable is on this side (metal grounding clip, indicated in orange). Repeat the above two steps.

    Make sure you pay close attention when removing the screw marked with a red circle that is in the left most position, as there’s a small grounding plate that will be completely unrestrained and free to get nice and lost only to be found later leaving you not knowing what the hell it is or where it came from should you not secure it before removing the panel that that screw secures. That grounding plate is crucial for the safety of yourself and your speaker, because it bridges the USB-micro power input jack to the metal frame. That means that should you lose it and put the speaker back together without it, your speaker will not be able to ground out and should there occur any surge during your charge cycle, like during a freak lightning storm, or whatever, your speaker won’t able to discharge that surge, which will no doubt fry your speaker, and likely kill whomever poor bastard happens to grab the speaker, say to turn it off during said storm as a safety precaution. SAFETY FIRST!

    Thousand Sunny -

    Btw, the screw I mentioned is shown in the third picture, since that small detail might have some play over success or failure in finding it…lol. Whoops.

    Thousand Sunny -

  4. Sh3tMvExQQTIIqZy

    • Pry up the bottom panel by lifting from the device.

    • Pull the bottom up. This may take a bit of force as the bottom is glued to device.

    • Once removed, the battery will now be visible.

    No glue on mine. Only two clips on each side (that you can see clearly in step 3 picture).

    Do not use force or you will break those clips.

    Jay -

    @jemdem (I assume this is the “Jay” involved) after looking at the pictures 3.1, 3.2, 3.3, I still don’t see what I would normally expect a “clip” to look like. Maybe the corners act as clips? If not, I can’t ‘clearly’ determine them, but it’s a fairly busy looking area with lots of recesses and all, so maybe they’re just blending in well?

    Thousand Sunny -

    There’s a plug on each foot in one of the corners that isn’t meant to be removed. The left one and the right one (when viewed so the writing appears correct way up), both have three pins and one plug, with the pins occupying three of the four corners (northeast, northwest etc.) and the plug occupying the remaining fourth corner. The left foot has pins in the upper right, upper left and lower left, and the plug which is part of the foot and plugs into the frame, is in the lower right corner, while the right foot is opposite, having pins in upper left, upper right and lower right, and the plug in the lower right. If that was too many ‘left’s and ‘right’s to follow along with, then just remember that the plug is on the lower-inside corner on each. The screw is in the center of each foot. If you pull too hard, or attempt to guide your pick/spudger all the way around when separating the foot, you could slice it right off, though adhesive will be needed for reapplying so severing isn’t the end of the world.

    Thousand Sunny -

    …continuing, the last foot needing removed is the upper center, when viewed so the writing on the feet is correct way up. And the plug on that foot is in the upper position, so only separate the bottom and both sides to access the screw in the center.

    Thousand Sunny -

    After continuing with the side pieces, the ‘clips’ that were holding the end pieces on were indeed at the corners and are NOT visible, clearly or otherwise. In fact only the ‘well’ or socket that each of the clips insert into are clearly shown, however the clips themselves are on the end caps, not the main body. If the speaker you are working on appears to have been dropped before and the corners are at all crumpled inward, take extra care to try and straighten them back to original shape before attempting to unclog the caps because not doing so could result in the clips breaking off. This may sound difficult, but I managed to straighten out all eight corners of the one I’m working on with no issues using a pair of needle nose pliers that are toothless so as to not introduce any bite patterns to the grill.

    Thousand Sunny -

  5. 4eLBA2VEVUdE31sC
    4eLBA2VEVUdE31sC
    ZpLHTRAIClrqjMfQ

    • Before unscrewing, take a picture of the top view. That way, when you're reassembling the device, you'll know the orientation of the metal grounding plates.

    • Unscrew the eight indicated T6 9.8 mm screws. Remove metal grounding plates.

    If you took the bottom off without noticing the orientation or taking a picture, worry not, my child. The speaker has a “jawbone” name plate on the front of it, but not the back that you can see in the above picture in the lower section of the face which is facing us in that picture. When you have the speaker oriented so the bottom is up, and the name plate is at the top, the words on the rubber feet should also face right side up when replacing the bottom panel. Though if you’re paying close enough attention, the bottom panel only correctly attaches one way and can’t correctly attach the other way around.

    Thousand Sunny -

  6. mE1t61rJL3kgyFPA

    • Once all eight screws are removed, pry the sides of the Jambox to lift the body from it's shell.

  7. SvF3JIkTNocSEpQL

    • With the battery facing forward, remove the three indicated T6 9.5 mm screws.

    • Once the screws are removed, lift up the small plastic plate, revealing the auxiliary board underneath.

  8. euqwStZNxILYpVNQ
    euqwStZNxILYpVNQ
    QWdQnoR2p1AM1EP1
    tMVY6eUQhOulFUDR

    • Place the disassembled Jambox with the speakers facing up.

    • Locate the screws around the broken speaker.

    • Use a T15 screwdriver to remove the four 12.1 mm screws around the broken speaker.

  9. KKZTVkDo5sLPin4P

    • Using a plastic opening tool, pry the speaker out of the Jambox.

  10. LBLNxpCLQfPaIZHI
    LBLNxpCLQfPaIZHI
    teCVhx65GdpR3RDT

    • Desolder the wires from the speaker terminal in the Jambox.

    • Detach the round speaker from its square frame, and save the square frame for the replacement speaker.

    • Use caution when operating a soldering iron due to extreme heat.

    • For instructions on how to solder and desolder, take a look at the soldering guide.

    Pessoal bom dia , onde consigo comprar o Auto Falante ?

    ronin496 -

    Fine, but where did you buy the new speaker ? I can’t find it.

    Fabrizio

    Fabrizio Dell'Anese -

    I’d like to know the speaker capacity or specifications in ohms and watts. If someone know I’ll really appreciate.

    Benjamin Hernandez -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Taryn Kelley

Member since: 02/04/15

678 Reputation

14 comments

What is actual original speaker size and watts power?

Phinlander Betancur -

Eu também gostaria de saber qual a potência e o tamanho exato do falante original para substituí-lo

I would also like to know the power and the exact size of the original speaker to replace it

francisnvieira -

Does anyone know where to buy replacement speakers or for which they can be switched?

olivierdegruijter -

@ Oliver,

I just wasted a pair of speakers because you mentioned those worked just fine for you. They are not the same sizes. it's smaller than the jamb speakers... On what basis you made that comment?

Kaveh Kadkhoda Zadeh -

bought mine (2 speakers x $18 bucks) replaced both and now is working and even louder. not gonna lie I had to cut on one side of the box where the speaker fits in but after ding it so and soldering the speakers now is working.

karloznyf -

does anyone know where to buy replacement parts - looking for the outer metal shell as it’s dented. thanks

aric.valliere -

What are the symptoms of the problems you guys are having?

Why do you think the speakers are the problem, and not the electronic amplifier?

Mine is sounding bad, and I’m pretty sure it’s from blown amplifier transistors, not the speakers…

Chris Drake -

hello chis drake, can u buy new amplifier transistors, and what make u think its not the speaker!?

wi dekker -

How do I know it’s the amplifier and not the speaker? Where can I find these parts for my jawbone jam box? Thank you anyone please?!

Juanita Diaz -

Informative disassembly tips.

Problem is……..

What speakers to use for replacements.

Please give dimensions, height and magnet size.

Wattage and ohms.

Thank You

BoB -

Many Years later, but... speakers are rectangular frame 56mm wide, screw holes 46mm.
Model: 130-00028
Found a company in Germany selling them, so i ordered and will see later.
hope it helped someone

Sean Booth -

https://oaudio.de/LAVOCE-FSN02071-2-full....

Not exact model but very very similar.
I will try them.

Sean Booth -

Thanks for reviving the thread!

did you note the ohms and watt rating?

If I search the speaker model number I get some choices on Amazon.

Cheers

2pcs 4ohm 8ohm speaker 2 inch Full Range Speaker Portable Speakers 10W 15W 20W Loudspeaker DIY HIFI BT Speakers(8ohm 20W) https://amzn.eu/d/aClOCl0

Jamie Little -