Google Pixel Tablet Speakers Replacement

Written By: Clay Eickemeyer

Comments: 5

Google Pixel Tablet Speakers Replacement

Difficulty

Moderate

Steps

Time Required

45 minutes - 1 hour

Introduction

This repair guide was authored by the iFixit staff and hasn’t been endorsed by Google. Learn more about our repair guides here.

Use this guide to replace the speakers in your Google Pixel Tablet.

If your tablet's audio sounds like static, is muffled, or is completely silent, your speakers might need to be replaced.

While this guide shows how to replace all speakers at once, use this guide to replace any of the four speakers.

Note: You'll need thin, double-sided tape, such as Tesa 61395 Tape to secure the screen and complete this repair.

Tools

Parts

Step 1

Allow your battery to fully drain before starting this repair. A charged battery may catch fire if damaged.
Unplug any cables from your tablet and fully power it down.
Hold the power and volume up buttons at the same time to bring up the power off menu.

What if your screen is so badly damaged you can't see the power off menu (or anything else on the screen)?

Lee Schneider -

Step 2

If your screen is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.

Step 3

The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method.
For complete instructions on how to use the Anti-Clamp, check out this guide.
Pull the blue handle backward to unlock the Anti-Clamp's arms.
Slide the arms over the top left corner, with one suction cup on the back cover and one on the screen.
Place an object under your tablet so it rests level between the Anti-Clamp's arms.
Squeeze the cups together to create suction.

Step 4

Pull the blue handle forward to lock the arms.
Turn the handle clockwise two full turns, or until the suction cups begin to stretch.
As the cups stretch, make sure they stay vertically aligned with each other. If they keep slipping, remove the Anti-Clamp and apply tape for the cups to stick to.

Step 5

Use a hair dryer or heat gun to heat the top left corner of the screen until a gap forms between the glass and the frame.
Be careful not to overheat the tablet—the screen and battery are susceptible to heat damage.
Insert an opening pick into the gap.
Remove the Anti-Clamp using the pull tabs on the suction cups.

Step 6

If you've already inserted an opening pick using the Anti-Clamp, skip down two steps.
Rotate your tablet so the front camera is closest to you.
Apply a heated iOpener to the top left corner of the screen (now your bottom right, since the tablet is flipped around) for three minutes.
You can also use a hair dryer, heat gun, or hot plate, but be careful not to overheat the screen or battery—only heat the tablet so it's warm to the touch.

Step 7

Apply a suction handle to the top left corner of the screen, as close to the top edge as possible.
Pull up on the suction handle with a strong, steady force until a gap forms between the glass and the frame.
Insert the tip of an opening pick into the gap.
Remove the suction handle.

This step is insanely hard. What the picture doesn't show is how to keep tablet from lifting off the table as you pull up. I've been at this step for an hour and the screen hasn't budged a half millimeter.

Bryan Gillespie -

Step 8

The screen is secured with adhesive all around the perimeter. Note the following areas as you separate the adhesive:
The top, bottom, and left edges have the thickest adhesive.
The right edge has slightly thinner adhesive.
At the top, near the front camera, the adhesive is very thin and delicate cables connect the screen to the frame.

Step 9

Don't insert your pick deeper than 7 mm, or about halfway between the tip of the pick and the iFixit logo.
Slide your opening pick to the top left corner of the tablet.
Leave this pick inserted to prevent the adhesive from resealing.

Step 10

Apply a heated iOpener to the left edge of the screen for two minutes.
You can also use a hair dryer, heat gun, or hot plate, but be careful not to overheat the screen or battery.

Step 11

Don't insert your pick deeper than 7 mm, or about halfway between the tip of the pick and the iFixit logo.
Insert a second opening pick in the top left corner of the screen.
Slide your pick to the bottom left corner of the screen to separate the left edge adhesive.
Leave this pick inserted to prevent the adhesive from resealing.

Step 12

Apply a heated iOpener to the bottom edge of the screen for two minutes.
You can also use a hair dryer, heat gun, or hot plate, but be careful not to overheat the screen or battery.

Step 13

Don't insert your pick deeper than 7 mm, or about halfway between the tip of the pick and the iFixit logo.
Insert a third opening pick in the bottom left corner.
Slide your pick to the bottom right corner of the screen to separate the bottom edge adhesive.
If your pick becomes stuck, repeatedly twist it as you slide to help separate the adhesive.
Leave this pick inserted to prevent the adhesive from resealing.

If your screen has cracks that extend to the edge, this step is insanely hard as well. The pick will not be able to slide cleanly under the crack boundaries. 10/10 difficulty repair for cracked screens.

Bryan Gillespie -

Step 14

Apply a heated iOpener to the right edge of the screen for two minutes.
You can also use a hair dryer, heat gun, or hot plate, but be careful not to overheat the screen or battery.

Step 15

Don't insert your pick deeper than 5 mm along the right edge.
For a visual reference, you can measure 5 mm from the tip and mark your pick with a permanent marker.
Insert a fourth opening pick in the bottom right corner.
Slide your pick to the top right corner to separate the right edge adhesive.
Leave this pick inserted to prevent the adhesive from resealing.

Step 16

Apply a heated iOpener to the top edge of the screen for two minutes.
You can also use a hair dryer, heat gun, or hot plate, but be careful not to overheat the screen or battery.

Step 17

The front camera and sensor are along the middle of the top edge. Be very careful not to insert your opening pick deeper than 3 mm (1/8 in) here.
For a visual reference, you can measure 3 mm from the tip and mark your pick with a permanent marker.
To mark where to avoid slicing too deep, it can be helpful to put a 6.3 cm (2.5 in) long strip of masking tape on the top edge, centered over the front camera.

Step 18

Insert a fifth opening pick in the top right corner of the screen.
Slide your pick toward the front camera. Stop when your pick is 3 cm (1.25 in) from the front camera.
Pull your pick out to a depth of 3 mm (1/8 inch) and slide it past the front camera.
When your pick is 3 cm past the front camera, insert it up to 6 mm deep, or about halfway between the tip and the iFixit logo, and slide it to the first pick you left in the top left corner.

Step 19

Don't tilt the screen open beyond 90 degrees. The front camera and sensor cables are very short and may tear.
Grab and lift the bottom corners of the screen.
If the screen feels stuck, check around the perimeter for any missed sections of adhesive and slice them with an opening pick.
Tilt the screen open just enough to access the cables connecting the screen to the frame.
During reassembly, remove the adhesive liners from the perimeter of the screen before firmly pressing it into place in the frame.

Step 20

For the next three steps, hold the screen tilted open with one hand while you work with your other hand.
If you have difficulty holding up the screen, place the tablet's dock on the frame to prop up the screen or ask someone to hold it up while you work.
Use tweezers to peel and remove the black tape off of the screen cable connector.
During reassembly:
Install new tape if the old piece is damaged and you have a replacement from your repair kit.
Now is a good time to test your tablet before sealing it up. Power it on and check that it works. Power it back down before you continue reassembly.

Step 21

Use the point of a spudger or a clean fingernail to flip up the small locking flap on the inside edge (same side as the cable) of the screen cable ZIF connector.
Use tweezers or your fingers to pull the screen cable straight out of its socket.

Step 22

Use an opening pick to flip up the small locking flap on the outside edge (opposite the cable) of the front camera ZIF connector.
Use tweezers to pull the cable straight out of its socket.
During reassembly, be careful not to tear this cable, since it doesn't have much room to bend. Guide the connector into its socket with tweezers and lock the ZIF connector flap at the same time.

Step 23

Use the point of your spudger or a clean fingernail to flip up the small locking flap on the inside edge of the front sensor connector.
Use tweezers to pull the cable straight out of its socket.

Step 24

Remove the screen.

Step 25

Follow the next two steps to clean your frame and prepare it for reassembly.
Use the flat end of your spudger or a clean fingernail to scrape up an edge of the leftover frame adhesive until you can grip it.
Use tweezers or your fingers to peel off large pieces of adhesive from the frame.
Repeat this process around the entire perimeter of the frame until there are no large pieces are left.
If you're reusing your screen, remove the old adhesive from it as well as the frame.

Step 26

Fill a pipette or syringe with highly-concentrated isopropyl alcohol (over 90%) and apply a few drops to the edge of the frame.
Wrap a microfiber or lint free cloth around the flat end of your spudger and scrub the frame until it's clean. Use more isopropyl alcohol as you go.
If you're reusing your screen, clean its perimeter as well as the frame.

Step 27

While the Pixel Tablet uses Torx Plus screws, standard Torx bits work in a pinch. Make sure to apply constant, downward force to prevent stripping.
Use a Torx Plus 3IP driver to remove the two 2.6 mm screws securing the battery, USB-C, and speakers connectors cover.
If you're using standard Torx bits, a T3 Torx will work best for these screws. If it feels too loose, you may need a T4 Torx bit.
Remove the cover.

Step 28

Use the flat end of your spudger to pry up and disconnect the battery press connector.
To reconnect a press connector, align it over its socket and gently press down on one side until it clicks into place, then press down on the other side.

Why we have to disconnect battery connector here if we only want to replace screen? for safety? or other concern? thanks.

Shiryu Lee -

Yes, you're right about safety! The wide screen cable is very delicate and prone to shorting if it's inserted wrong. The danger is reflected in the reassembly step farther down in the guide. Essentially, you risk shorting the connector and creating a fire hazard if power runs through an improperly connected screen cable.

Clay Eickemeyer -

Step 29

Connecting the screen cable with the battery connected risks shorting the connector and poses a fire hazard.
Follow this step during reassembly to safely reconnect the screen and battery.
Prop up the bottom edge of the tablet on a box or similar object. Tilt the screen open and lean it against something so that it's angled up to 90 degrees.
Reconnect the small front sensor cable ZIF connector.
Reconnect the large screen cable ZIF connector.
Reconnect the battery press connector.
Use your Torx Plus 3IP driver to install the two 2.6 mm screws and fasten the connector cover.
Continue reassembly with these cables connected.

Step 30

Use the flat end of your spudger to pry up and disconnect the USB-C port press connector.

Step 31

Be careful not to damage the battery with your tool during this step.
Use blunt nose tweezers or your fingers to peel up and remove the three strips of tape securing the USB-C port cable to the battery.
During reassembly, reuse these strips of tape if they're in good condition. If not, cut and apply a few thin strips of electrical tape to re-secure the cable to the battery.

Step 32

Use your Torx Plus 3IP driver to remove the four 3.2 mm screws securing the USB-C port.

Step 33

Pull the USB-C port out of its recess in the frame and remove it.

Step 34

Use the point of your spudger to lift up and disconnect the blue and white speaker cable connector from the right side of the logic board.
Pry straight up on the neck of the cables, as close to the head of the connector as possible.
Disconnect the red and black speaker cable connector.

Step 35

Pull the blue and white speaker cables out from their clips along the top and right edges of the battery tray.
Pull the red and black speaker cables out from their clips along the top of the battery tray.

Step 36

Use the point of your spudger to lift up and disconnect the blue and white speaker cable connector from the left side of the logic board.
Pry straight up on the neck of the cables, as close to the head of the connector as possible.
Disconnect the black and white speaker cable connector.

Step 37

Pull the blue and white speaker cable out from their clips along the top and left edges of the battery tray.
Pull the black and white speaker cable out from their clips along the top edge of the battery tray.

Step 38

Use blunt nose tweezers or your fingers to peel up and remove the tape securing the black and white speaker cable to the frame.
During reassembly, reuse this tape if it's in good condition. If not, cut and apply a thin strip of electrical tape to re-secure the cables to the frame.

Step 39

Use a Torx Plus 2IP driver to remove the sixteen 2.7 mm screws securing the four speakers.
If you're using standard Torx bits, a T3 Torx will work best for these screws. If it feels too tight, you may need a T2 Torx bit.