1999–2005: Creation and introduction of smaller formats

In 1999, SanDisk, Panasonic (Matsushita), and Toshiba agreed to develop and market the Secure Digital (SD) memory card.^[5] The card was derived from the MultiMediaCard (MMC) and provided digital rights management (DRM) based on the Secure Digital Music Initiative (SDMI) standard and a high memory density.

SD was designed to compete with the Memory Stick, a DRM product Sony had released the year before. Toshiba hoped its DRM would encourage music suppliers concerned about piracy to use SD cards.^[6]

The trademarked SD logo was originally developed for the Super Density Disc, which was the unsuccessful Toshiba entry in the DVD format war. For this reason, the letter "D" is styled to resemble an optical disc.^[7]

At the 2000 Consumer Electronics Show (CES), the three companies announced the creation of the SD Association (SDA) to promote SD cards. The SD Association, which was headquartered in San Ramon, California, United States, then had 30 member companies and product manufacturers that made interoperable memory cards and devices. Early samples of the SD card^[8] became available in the first quarter of 2000, and production quantities of 32 and 64 megabyte (MB)^{[lower-alpha 1]} cards became available three months later.

miniSD

microSD card in a smartphone

At March 2003 CeBIT, SanDisk Corporation introduced, announced, and demonstrated the miniSD form factor.^[9] The SDA adopted the miniSD card in 2003 as a small-form-factor extension to the SD card standard. While the new cards were designed for mobile phones, they were usually packaged with a miniSD adapter that provided compatibility with a standard SD memory card slot.

2006–2008: SDHC and SDIO

This microSDHC card holds 8 billion bytes. Beneath it is a section of a magnetic-core memory (used until the 1970s) that holds eight bytes using 64 cores. The card covers approximately 20 bits (2+1⁄2 bytes).

In September 2006, SanDisk announced the 4 GB miniSDHC.^[12] Like the SD and SDHC, the miniSDHC card has the same form factor as the older miniSD card but the HC card requires HC support built into the host device. Devices that support miniSDHC work with miniSD and miniSDHC, but devices without specific support for miniSDHC work only with the older miniSD card. Since 2008, miniSD cards are no longer produced, due to market domination of the even smaller microSD cards.

2009–2019: SDXC

Macro shot of a microSDXC memory card with eight gold plated electrical contacts

The storage density of memory cards increased significantly throughout the 2010s, allowing the earliest devices to offer support for the SD:XC standard, such as the Samsung Galaxy S III and Samsung Galaxy Note II mobile phones, to expand their available storage to several hundreds of gigabytes.

In January 2009, the SDA announced the SDXC family, which supports cards up to 2 TB^{[lower-alpha 2]} and speeds up to 300 MB/s.^[13] SDXC cards are formatted with the exFAT file system by default.^[14] SDXC was announced at Consumer Electronics Show (CES) 2009 (January 7–10). At the same show, SanDisk and Sony also announced a comparable Memory Stick XC variant with the same 2 TB^{[lower-alpha 2]} maximum as SDXC,^[15] and Panasonic announced plans to produce 64 GB SDXC cards.^[16] On March 6, Pretec introduced the first SDXC card,^[17] a 32 GB card with a read/write speed of 400 Mbit/s. But only early in 2010 did compatible host devices come onto the market, including Sony's Handycam HDR-CX55V camcorder, Canon's EOS 550D (also known as Rebel T2i) Digital SLR camera,^[18] a USB card reader from Panasonic, and an integrated SDXC card reader from JMicron.^[19] The earliest laptops to integrate SDXC card readers relied on a USB 2.0 bus, which does not have the bandwidth to support SDXC at full speed.^[20]

In early 2010, commercial SDXC cards appeared from Toshiba (64 GB),^[21][22] Panasonic (64 GB and 48 GB),^[23] and SanDisk (64 GB).^[24]

In early 2011, Centon Electronics, Inc. (64 GB and 128 GB) and Lexar (128 GB) began shipping SDXC cards rated at Speed Class 10.^[25] Pretec offered cards from 8 GB to 128 GB rated at Speed Class 16.^[26] In September 2011, SanDisk released a 64 GB microSDXC card.^[27] Kingmax released a comparable product in 2011.^[28]

In April 2012, Panasonic introduced MicroP2 card format for professional video applications. The cards are essentially full-size SDHC or SDXC UHS-II cards, rated at UHS Speed Class U1.^[29][30] An adapter allows MicroP2 cards to work in current P2 card equipment.^[31]

Panasonic MicroP2 cards shipped in March 2013 and were the first UHS-II compliant products on market; initial offer includes a 32 GB SDHC card and a 64 GB SDXC card.^[29][32] Later that year, Lexar released the first 256 GB SDXC card, based on 20 nm NAND flash technology.^[33]

In February 2014, SanDisk introduced the first 128 GB microSDXC card,^[34] which was followed by a 200 GB microSDXC card in March 2015.^[35] September 2014 saw SanDisk announce the first 512 GB SDXC card.^[36]

Samsung announced the world's first EVO Plus 256 GB microSDXC card in May 2016,^[37] and in September 2016 Western Digital (SanDisk) announced that a prototype of the first 1 TB^{[lower-alpha 3]} SDXC card would be demonstrated at Photokina.^[38]

In August 2017, SanDisk launched a 400 GB microSDXC card.^[39]

In January 2018, Integral Memory unveiled its 512 GB microSDXC card.^[40] In May 2018, PNY launched a 512 GB microSDXC card. In June 2018 Kingston announced its Canvas series of MicroSD cards which were capable of capacities up to 512 GB,^{[lower-alpha 4]} in three variations, Select, Go!, and React.^[41]

In February 2019, Micron and SanDisk unveiled their microSDXC cards of 1 TB capacity.^[42]

2019–present: SDUC

The Secure Digital Ultra Capacity (SDUC) format supports cards up to 128 TB^{[lower-alpha 2]} and offers speeds up to 985 MB/s.

SD (SDSC)

Secure Digital Standard Capacity (SD) logo. The specification defines cards with a capacity of up to 2 GB.

The second-generation Secure Digital (SDSC or Secure Digital Standard Capacity) card was developed to improve on the MultiMediaCard (MMC) standard, which continued to evolve, but in a different direction. Secure Digital changed the MMC design in several ways:

• Asymmetrical shape of the sides of the SD card prevents inserting it upside down (whereas an MMC goes in most of the way but makes no contact if inverted).
• Most standard size SD cards are 2.1 mm (0.083 inches)^[46] thick, with microSD versions being 1.0 mm (0.039 inches)^[46] thick, compared to 1.4 mm (0.055 inches) for MMCs. The SD specification defines a card called Thin SD with a thickness of 1.4 mm, but they occur only rarely, as the SDA went on to define even smaller form factors.
• The card's electrical contacts are recessed beneath the surface of the card, protecting them from contact with a user's fingers.
• The SD specification envisioned capacities and transfer rates exceeding those of MMC, and both of these functionalities have grown over time. For a comparison table, see below.
• While MMC uses a single pin for data transfers, the SD card added a four-wire bus mode for higher data rates.
• The SD card added Content Protection for Recordable Media (CPRM) security circuitry for digital rights management (DRM) content-protection.
• Addition of a write-protect notch

Full-size SD cards do not fit into the slimmer MMC slots, and other issues also affect the ability to use one format in a host device designed for the other.

SDHC

Secure Digital High Capacity (SDHC) logo. The specification defines cards with a capacity of more than 2 GB up to 32 GB.

The Secure Digital High Capacity (SDHC) format, announced in January 2006 and defined in version 2.0 of the SD specification, supports cards with capacities up to 32 GB.^{[lower-alpha 4][43]} The SDHC trademark is licensed to ensure compatibility.^[47]

SDHC cards are physically and electrically identical to standard-capacity SD cards (SDSC). The major compatibility issues between SDHC and SDSC cards are the redefinition of the Card-Specific Data (CSD) register in version 2.0 (see below), and the fact that SDHC cards are shipped preformatted with the FAT32 file system.

Version 2.0 also introduces a High-speed bus mode for both SDSC and SDHC cards, which doubles the original Standard Speed clock to produce 25 MB/s.^[48]

SDHC host devices are required to accept older SD cards.^[49] However, older host devices do not recognize SDHC or SDXC memory cards, although some devices can do so through a firmware upgrade.^[50] Older Windows operating systems released before Windows 7 require patches or service packs to support access to SDHC cards.^[51][52][53]

SDXC

Secure Digital eXtended Capacity logo. The specification defines cards with a capacity of more than 32 GB up to 2 TB.

The Secure Digital eXtended Capacity (SDXC) format, announced in January 2009 and defined in version 3.01 of the SD specification, supports cards up to 2 TB,^{[lower-alpha 2]} compared to a limit of 32 GB^{[lower-alpha 4]} for SDHC cards in the SD 2.0 specification. SDXC adopts Microsoft's exFAT file system as a mandatory feature.^[54]

Version 3.01 also introduced the Ultra High Speed (UHS) bus for both SDHC and SDXC cards, with interface speeds from 50 MB/s to 104 MB/s for four-bit UHS-I bus.^[55] (this number has since been exceeded with SanDisk proprietary technology for 170 MB/s read, which is not proprietary anymore, as Lexar has the 1066x running at 160 MB/s read and 120 MB/s write via UHS 1, and Kingston also has their Canvas Go! Plus, also running at 170 MB/s).^{[56][57][58][59]}

Version 4.0, introduced in June 2011, allows speeds of 156 MB/s to 312 MB/s over the four-lane (two differential lanes) UHS-II bus, which requires an additional row of physical pins.^[55]

Version 5.0 was announced in February 2016 at CP+ 2016, and added "Video Speed Class" ratings for UHS cards to handle higher resolution video formats like 8K.^[60][61] The new ratings define a minimal write speed of 90 MB/s.^[62][63]

SDUC

Secure Digital Ultra Capacity (SDUC) logo. The specification defines cards with a capacity of more than 2 TB up to 128 TB.

The Secure Digital Ultra Capacity (SDUC) format, described in the SD 7.0 specification, and announced in June 2018, supports cards up to 128 TB^{[lower-alpha 2]} and offers speeds up to 985 MB/s, regardless of form factor, either micro or full size, or interface type including UHS-I, UHS-II, UHS-III or SD Express.^[64] The SD Express interface can also be used with SDHC and SDXC cards.

Comparison

Comparison of SD card capacity standards^[75]

		SD	SDHC	SDXC	SDUC
Logo
Capacity	Min	0	>2 GB	>32 GB	>2 TB
	Max	2 GB	32 GB	2 TB	128 TB
Typical FS		FAT12/FAT16	FAT32	exFAT

Bus

Ultra High Speed (UHS)

The Ultra High Speed (UHS) bus is available on some SDHC and SDXC cards.^[81][82][83]

Cards that comply with UHS show Roman numerals 'I', 'II' or 'III' next to the SD card logo,^[81][79] and report this capability to the host device. Use of UHS-I requires that the host device command the card to drop from 3.3-volt to 1.8-volt operation over the I/O interface pins and select the four-bit transfer mode, while UHS-II requires 0.4-volt operation.

The higher speed rates of UHS-II and III are achieved by using two-lane 0.4 V Low-voltage differential signaling (LVDS) on a second row of pins.^[84] Each lane is capable of transferring up to 156 MB/s. In full-duplex mode, one lane is used for Transmit while the other is used for Receive. In half-duplex mode both lanes are used for the same direction of data transfer allowing a double data rate at the same clock speed. In addition to enabling higher data rates, the UHS-II interface allows for lower interface power consumption, lower I/O voltage and lower electromagnetic interference (EMI).

The following ultra-high speeds are specified:

UHS-I

Specified in SD version 3.01.^[85] Supports a clock frequency of 100 MHz (a quadrupling of the original "Default Speed"), which in four-bit transfer mode could transfer 50 MB/s (SDR50). UHS-I cards declared as UHS104 (SDR104) also support a clock frequency of 208 MHz, which could transfer 104 MB/s. Double data rate operation at 50 MHz (DDR50) is also specified in Version 3.01, and is mandatory for microSDHC and microSDXC cards labeled as UHS-I. In this mode, four bits are transferred when the clock signal rises and another four bits when it falls, transferring an entire byte on each full clock cycle, hence a 50 MB/s operation could be transferred using a 50 MHz clock.

There is a proprietary UHS-I extension, called DDR200, originally created by SanDisk that increases transfer speed further to 170 MB/s. Unlike UHS-II, it does not use additional pins. It achieves this by using the 208 MHz frequency of the standard SDR104 mode, but using DDR transfers.^[86][87] This extension has since then been used by Lexar for their 1066x series (160 MB/s), Kingston Canvas Go Plus (170 MB/s) and the MyMemory PRO SD card (180 MB/s).

UHS-II

Back side of a Lexar UHS-II microSDHC card, showing the additional row of UHS-II connections

Specified in version 4.0, further raises the data transfer rate to a theoretical maximum of 156 MB/s (full-duplex) or 312 MB/s (half-duplex) using an additional row of pins for LVDS signalling^[88] (a total of 17 pins for full-size and 16 pins for micro-size cards).^[81] While first implementations in compact system cameras were seen three years after specification (2014), it took many more years until UHS-II was implemented on a regular basis. At the beginning of 2021, there were more than 50 DSLR and compact system cameras using UHS-II.^[89]

UHS-III

Version 6.0, released in February 2017, added two new data rates to the standard. FD312 provides 312 MB/s while FD624 doubles that. Both are full-duplex. The physical interface and pin-layout are the same as with UHS-II, retaining backward compatibility.^[90]

SD Express

Front and back of an SD Express card

The SD Express bus was released in June 2018 with SD specification 7.0. It uses a single PCIe lane to provide full-duplex 985 MB/s transfer speed. Supporting cards must also implement the NVM Express storage access protocol. The Express bus can be implemented by SDHC, SDXC, and SDUC cards. For legacy application use, SD Express cards must also support High-Speed bus and UHS-I bus. The Express bus re-uses the pin layout of UHS-II cards and reserves the space for additional two pins that may be introduced in the future.^[91]

Hosts which implement version 7.0 of the spec allow SD Cards to do direct memory access, which increases the attack surface of the host dramatically in the face of malicious SD cards.^[92]

Version 8.0 was announced on 19 May 2020, with support for two PCIe lanes with an additional row of contacts and PCIe 4.0 transfer rates, for a maximum bandwidth of 3938 MB/s.^[93]

Version 9.0 was released in February 2022.^[94]

microSD Express

In February 2019, the SD Association announced microSD Express.^[95] The microSD Express cards offer PCI Express and NVMe interfaces, as the June 2018 SD Express release did, alongside the legacy microSD interface for continued backwards compatibility. The SDA also released visual marks to denote microSD Express memory cards to make matching the card and device easier for optimal device performance.^[96]

Bus speed comparison

Comparison of SD card bus speeds^[97]

Bus interface	Bus logo	Bus speed	PCI Express lanes	Duplex	Card types				Spec version
					SD	SDHC	SDXC	SDUC
Default Speed	—	00,012.5 MB/s	—	?	Yes	Yes	Yes	Yes	1.01
High Speed		0025 MB/s							1.10
UHS-I		0050 MB/s		Half / Full	No				3.01
		0104 MB/s		Half
	—	0180 MB/s[lower-alpha 5]							—
UHS-II		0156 MB/s		Full					4.00
		0312 MB/s		Half
UHS-III		0312 MB/s		Full					6.00
		0624 MB/s
SD Express		0985 MB/s	3.1 ×1						7.00
		1969 MB/s	3.1 ×2						8.00
			4.0 ×1
		3938 MB/s	4.0 ×2

Class

64GB SanDisk Ultra microSDXC card (with UHS-I and UHS Speed Class 1 markings)

32GB Lexar 1000x microSDHC card (with UHS-II and UHS Speed Class 3 markings)

The front and back of the Sony 64GB SF-M Tough Series UHS-II SDXC Memory Card

The SD Association defines standard speed classes for SDHC/SDXC cards indicating minimum performance (minimum serial data writing speed). Both read and write speeds must exceed the specified value. The specification defines these classes in terms of performance curves that translate into the following minimum read-write performance levels on an empty card and suitability for different applications:^{[85][79][99][100]}

The SD Association defines three types of Speed Class ratings: the original Speed Class, UHS Speed Class, and Video Speed Class.

Comparison

Top: A 128 GB CFexpress Type B card by Panasonic (1700 MBit/s reading) next to 256 GB SD card V30 (160 MBit/s reading) by Samsung
Bottom: Bottom view showing SD card contacts

Comparison of SD card Speed Class ratings^[102]

Minimum sequential writing speed	Suggested max. bitrate	Speed Class			Video format[lower-alpha 6]
		Speed Class	UHS Speed Class	Video Speed Class	SD	HD / Full HD	4K	8K
02 MB/s	015 Mbit/s	Class 2 (C2)	—	—	Yes	No	No	No
04 MB/s	030 Mbit/s	Class 4 (C4)				Yes
06 MB/s	045 Mbit/s	Class 6 (C6)		Class 6 (V6)			Yes
10 MB/s	075 Mbit/s	Class 10 (C10)	Class 1 (U1)	Class 10 (V10)
30 MB/s	220 Mbit/s		Class 3 (U3)	Class 30 (V30)				Yes
60 MB/s	460 Mbit/s			Class 60 (V60)
90 MB/s	700 Mbit/s			Class 90 (V90)

Application Performance Class

Application Performance Class is a newly defined standard from the SD Specification 5.1 and 6.0 which not only define sequential Writing Speeds but also mandates a minimum IOPS for reading and writing. Class A1 requires a minimum of 1500 reading and 500 writing operations per second, while class A2 requires 4000 and 2000 IOPS.^[103] A2 class cards require host driver support as they use command queuing and write caching to achieve their higher speeds. Without they are guaranteed to at least reach A1 speeds. As of kernel 5.15, Linux fully supports A2.^[104]

Comparison of SD card Application Performance Class ratings^[105]

Name	Minimum random IOPS		Minimum sustained sequential writing
	Read	Write
Application Performance Class 1 (A1)	1500 IOPS	0500 IOPS	10 MB/s
Application Performance Class 2 (A2)	4000 IOPS	2000 IOPS

"×" rating

Main article: CD and DVD writing speed

Rating	Approx. (MB/s)	Comparable Speed Class
16×	2.34	(13×)
32×	4.69	(27×)
48×	7.03	(40×)
100×	14.6	(67×)

The "×" rating, which was used by some card manufacturers and made obsolete by speed classes, is a multiple of the standard CD-ROM drive speed of 150 KB/s^{[lower-alpha 7]} (approximately 1.23 Mbit/s). Basic cards transfer data at up to six times (6×) the CD-ROM speed; that is, 900 kbit/s or 7.37 Mbit/s. The 2.0 specification defines speeds up to 200×, but is not as specific as Speed Classes are on how to measure speed. Manufacturers may report best-case speeds and may report the card's fastest read speed, which is typically faster than the write speed. Some vendors, including Transcend and Kingston, report their cards' write speed.^[106] When a card lists both a speed class and an "×" rating, the latter may be assumed a read speed only.

Real-world performance

In applications that require sustained write throughput, such as video recording, the device might not perform satisfactorily if the SD card's class rating falls below a particular speed. For example, a high-definition camcorder may require a card of not less than Class 6, suffering dropouts or corrupted video if a slower card is used. Digital cameras with slow cards may take a noticeable time after taking a photograph before being ready for the next, while the camera writes the first picture.

The speed class rating does not totally characterize card performance. Different cards of the same class may vary considerably while meeting class specifications. A card's speed depends on many factors, including:

• The frequency of soft errors that the card's controller must re-try
• Write amplification: The flash controller may need to overwrite more data than requested. This has to do with performing read-modify-write operations on write blocks, freeing up (the much larger) erase blocks, while moving data around to achieve wear leveling.
• File fragmentation: where there is not sufficient space for a file to be recorded in a contiguous region, it is split into non-contiguous fragments. This does not cause rotational or head-movement delays as with electromechanical hard drives, but may decrease speed⁠ ⁠ ⁠—  for instance, by requiring additional reads and computation to determine where on the card the file's next fragment is stored.

In addition, speed may vary markedly between writing a large amount of data to a single file (sequential access, as when a digital camera records large photographs or videos) and writing a large number of small files (a random-access use common in smartphones). A study in 2012 found that, in this random-access use, some Class 2 cards achieved a write speed of 1.38 MB/s, while all cards tested of Class 6 or greater (and some of lower Classes; lower Class does not necessarily mean better small-file performance), including those from major manufacturers, were over 100 times slower.^[76] In 2014, a blogger measured a 300-fold performance difference on small writes; this time, the best card in this category was a class 4 card.^[77]

Card security

Write-protect notch

Unlocked and locked SD cards

Sony 64GB SF-M Tough Series UHS-II SDXC Memory Card is one of the few cards in the market without a sliding tab on the write protect notch.

Most full-size SD cards have a "mechanical write protect switch" allowing the user to advise the host computer that the user wants the device to be treated as read-only. This does not protect the data on the card if the host is compromised: "It is the responsibility of the host to protect the card. The position [i.e., setting] of the write protect switch is unknown to the internal circuitry of the card."^[109] Some host devices do not support write protection, which is an optional feature of the SD specification, and drivers and devices that do obey a read-only indication may give the user a way to override it.

The switch is a sliding tab that covers a notch in the card. The miniSD and microSD formats do not directly support a write protection notch, but they can be inserted into full-size adapters which do.

When looking at the SD card from the top, the right side (the side with the beveled corner) must be notched.

On the left side, there may be a write-protection notch. If the notch is omitted, the card can be read and written. If the card is notched, it is read-only. If the card has a notch and a sliding tab which covers the notch, the user can slide the tab upward (toward the contacts) to declare the card read/write, or downward to declare it read-only. The diagram to the right shows an orange sliding write-protect tab in both the unlocked and locked positions.

Cards sold with content that must not be altered are permanently marked read-only by having a notch and no sliding tab.

Card password

MicroSD-to-SD adapter (left), microSD-to-miniSD adapter (middle), microSD card (right)

A host device can lock an SD card using a password of up to 16 bytes, typically supplied by the user. A locked card interacts normally with the host device except that it rejects commands to read and write data. A locked card can be unlocked only by providing the same password. The host device can, after supplying the old password, specify a new password or disable locking. Without the password (typically, in the case that the user forgets the password), the host device can command the card to erase all the data on the card for future re-use (except card data under DRM), but there is no way to gain access to the existing data.

Windows Phone 7 devices use SD cards designed for access only by the phone manufacturer or mobile provider. An SD card inserted into the phone underneath the battery compartment becomes locked "to the phone with an automatically generated key" so that "the SD card cannot be read by another phone, device, or PC".^[110] Symbian devices, however, are some of the few that can perform the necessary low-level format operations on locked SD cards. It is therefore possible to use a device such as the Nokia N8 to reformat the card for subsequent use in other devices.^[111]

smartSD cards

A smartSD memory card is a microSD card with an internal "secure element" that allows the transfer of ISO 7816 Application Protocol Data Unit commands to, for example, JavaCard applets running on the internal secure element through the SD bus.^[112]

Some of the earliest versions of microSD memory cards with secure elements were developed in 2009 by DeviceFidelity, Inc.,^[113][114] a pioneer in near field communication (NFC) and mobile payments, with the introduction of In2Pay and CredenSE products, later commercialized and certified for mobile contactless transactions by Visa in 2010.^[115] DeviceFidelity also adapted the In2Pay microSD to work with the Apple iPhone using the iCaisse, and pioneered the first NFC transactions and mobile payments on an Apple device in 2010.^{[116][117][118]}

Various implementations of smartSD cards have been done for payment applications and secured authentication.^[119][120] In 2012 Good Technology partnered with DeviceFidelity to use microSD cards with secure elements for mobile identity and access control.^[121]

microSD cards with Secure Elements and NFC (near field communication) support are used for mobile payments, and have been used in direct-to-consumer mobile wallets and mobile banking solutions, some of which were launched by major banks around the world, including Bank of America, US Bank, and Wells Fargo,^{[122][123][124]} while others were part of innovative new direct-to-consumer neobank programs such as moneto, first launched in 2012.^{[125][126][127][128]}

microSD cards with Secure Elements have also been used for secure voice encryption on mobile devices, which allows for one of the highest levels of security in person-to-person voice communications.^[129] Such solutions are heavily used in intelligence and security.

In 2011, HID Global partnered with Arizona State University to launch campus access solutions for students using microSD with Secure Element and MiFare technology provided by DeviceFidelity, Inc.^[130][131] This was the first time regular mobile phones could be used to open doors without need for electronic access keys.

Vendor enhancements

Eye-Fi Mobi 16 GB

Toshiba FlashAir 16 GB

PQI air card 4 GB

Transcend Wi-Fi 16 GB

SD cards with dual interfaces: SD and USB

Vendors have sought to differentiate their products in the market through various vendor-specific features:

• Integrated Wi-Fi – Several companies produce SD cards with built-in Wi-Fi transceivers supporting static security (WEP 40; 104; and 128, WPA-PSK, and WPA2-PSK). The card lets any digital camera with an SD slot transmit captured images over a wireless network, or store the images on the card's memory until it is in range of a wireless network. Examples include: Eye-Fi / SanDisk, Transcend Wi-Fi, Toshiba FlashAir, Trek Flucard, PQI Air Card and LZeal ez Share.^[132] Some models geotag their pictures.
• Pre-loaded content – In 2006, SanDisk announced Gruvi, a microSD card with extra digital rights management features, which they intended as a medium for publishing content. SanDisk again announced pre-loaded cards in 2008, under the slotMusic name, this time not using any of the DRM capabilities of the SD card.^[133] In 2011, SanDisk offered various collections of 1000 songs on a single slotMusic card for about $40,^[134] now restricted to compatible devices and without the ability to copy the files.
• Integrated USB connector – The SanDisk SD Plus product can be plugged directly into a USB port without needing a USB card reader.^[135] Other companies introduced comparable products, such as the Duo SD product of OCZ Technology and the 3 Way (microSDHC, SDHC, and USB) product of A-DATA, which was available in 2008 only.
• Different colors – SanDisk has used various colors of plastic or adhesive label, including a "gaming" line in translucent plastic colors that indicated the card's capacity.
• Integrated display – In 2006, A-DATA announced a Super Info SD card with a digital display that provided a two-character label and showed the amount of unused memory on the card.^[136]

SDIO cards

Camera using the SDIO interface to connect to some HP iPAQ devices

A SDIO (Secure Digital Input Output) card is an extension of the SD specification to cover I/O functions. SDIO cards are only fully functional in host devices designed to support their input-output functions (typically PDAs like the Palm Treo, but occasionally laptops or mobile phones). These devices can use the SD slot to support GPS receivers, modems, barcode readers, FM radio tuners, TV tuners, RFID readers, digital cameras, and interfaces to Wi-Fi, Bluetooth, Ethernet, and IrDA. Many other SDIO devices have been proposed, but it is now more common for I/O devices to connect using the USB interface.

SDIO cards support most of the memory commands of SD cards. SDIO cards can be structured as eight logical cards, although currently, the typical way that an SDIO card uses this capability is to structure itself as one I/O card and one memory card.

The SDIO and SD interfaces are mechanically and electrically identical. Host devices built for SDIO cards generally accept SD memory cards without I/O functions. However, the reverse is not true, because host devices need suitable drivers and applications to support the card's I/O functions. For example, an HP SDIO camera usually does not work with PDAs that do not list it as an accessory. Inserting an SDIO card into any SD slot causes no physical damage nor disruption to the host device, but users may be frustrated that the SDIO card does not function fully when inserted into a seemingly compatible slot. (USB and Bluetooth devices exhibit comparable compatibility issues, although to a lesser extent thanks to standardized USB device classes and Bluetooth profiles.)

The SDIO family comprises Low-Speed and Full-Speed cards. Both types of SDIO cards support SPI and one-bit SD bus types. Low-Speed SDIO cards are allowed to also support the four-bit SD bus; Full-Speed SDIO cards are required to support the four-bit SD bus. To use an SDIO card as a "combo card" (for both memory and I/O), the host device must first select four-bit SD bus operation. Two other unique features of Low-Speed SDIO are a maximum clock rate of 400 kHz for all communications, and the use of Pin 8 as "interrupt" to try to initiate dialogue with the host device.^[137]

Compatibility

Wi-Fi/DAB+/FM/CD/MP3/WMA/USB/SDHC/podcast stereo recorder with iPod dock

Host devices that comply with newer versions of the specification provide backward compatibility and accept older SD cards.^[49] For example, SDXC host devices accept all previous families of SD memory cards, and SDHC host devices also accept standard SD cards.

Older host devices generally do not support newer card formats, and even when they might support the bus interface used by the card,^[44] there are several factors that arise:

• A newer card may offer greater capacity than the host device can handle (over 4 GB for SDHC, over 32 GB for SDXC).
• A newer card may use a file system the host device cannot navigate (FAT32 for SDHC, exFAT for SDXC)
• Use of an SDIO card requires the host device be designed for the input/output functions the card provides.
• The hardware interface of the card was changed starting with the version 2.0 (new high-speed bus clocks, redefinition of storage capacity bits) and SDHC family (Ultra-high speed (UHS) bus)
• UHS-II has physically more pins but is backwards compatible to UHS-I and non-UHS for both slot and card.^[81]
• Some vendors produced SDSC cards above 1 GB before the SDA had standardized a method of doing so.

Mobile phones

The microSD card has helped propel the smartphone market by giving both manufacturers and consumers greater flexibility and freedom.

While cloud storage depends on stable internet connection and sufficiently voluminous data plans, memory cards in mobile devices provide location-independent and private storage expansion with much higher transfer rates and no network delay, enabling applications such as photography and video recording. While data stored internally on bricked devices is inaccessible, data stored on the memory card can be salvaged and accessed externally by the user as mass storage device. A benefit over USB on the go storage expansion is uncompromised ergonomy. The usage of a memory card also protects the mobile phone's non-replaceable internal storage from weardown from heavy applications such as excessive camera usage and portable FTP server hosting over WiFi Direct. Due to the technical development of memory cards, users of existing mobile devices are able to expand their storage further and priceworthier with time.^{[140][141][142]}

Recent versions of major operating systems such as Windows Mobile and Android allow applications to run from microSD cards, creating possibilities for new usage models for SD cards in mobile computing markets, as well as clearing available internal storage space.^[143]

SD cards are not the most economical solution in devices that need only a small amount of non-volatile memory, such as station presets in small radios. They may also not present the best choice for applications that require higher storage capacities or speeds as provided by other flash card standards such as CompactFlash. These limitations may be addressed by evolving memory technologies, such as the new SD 7.0 specifications which allow storage capabilities of up to 128 TB.^{[lower-alpha 2][144]}

Many personal computers of all types, including tablets and mobile phones, use SD cards, either through built-in slots or through an active electronic adapter. Adapters exist for the PC card, ExpressBus, USB, FireWire, and the parallel printer port. Active adapters also let SD cards be used in devices designed for other formats, such as CompactFlash. The FlashPath adapter lets SD cards be used in a floppy disk drive.

Some devices such as the Samsung Galaxy Fit (2011) and Samsung Galaxy Note 8.0 (2013) have an SD card compartment located externally and accessible by hand, while it is located under the battery cover on other devices. More recent mobile phones use a pin-hole ejection system for the tray which houses both the memory card and SIM card.

Counterfeits

Samsung Pro 64 GB microSDXC original (left) and counterfeit (right): The counterfeit claims to have 64 GB in capacity, but only 8 GB (Class 4 speed) are usable: When trying to write more than 8 GB, data loss occurs. Also used for SanDisk 64 GB fakes.

Images of genuine, questionable, and counterfeit microSD (Secure Digital) cards before and after decapsulation. Details at source, photo by Andrew Huang.

Commonly found on the market are mislabeled or counterfeit Secure Digital cards that report a fake capacity or run slower than labeled.^{[145][146][147]} Software tools exist to check and detect counterfeit products.^[148][149] Detection of counterfeit cards usually involves copying files with random data to the SD card until the card's capacity is reached, and copying them back. The files that were copied back can be tested either by comparing checksums (e.g. MD5), or trying to compress them. The latter approach leverages the fact that counterfeited cards let the user read back files, which then consist of easily compressible uniform data (for example, repeating 0xFFs).

Digital cameras

SD card in a DSLR camera

Secure Digital memory cards can be used in Sony XDCAM EX camcorders with an adapter.^[150]

Personal computers

Although many personal computers accommodate SD cards as an auxiliary storage device using a built-in slot, or can accommodate SD cards by means of a USB adapter, SD cards cannot be used as the primary hard disk through the onboard ATA controller, because none of the SD card variants support ATA signalling. Primary hard disk use requires a separate SD host controller^[151] or an SD-to-CompactFlash converter. However, on computers that support bootstrapping from a USB interface, an SD card in a USB adapter can be the boot disk, provided it contains an operating system that supports USB access once the bootstrap is complete.

In laptop and tablet computers, memory cards in an integrated memory card reader offer an ergonomical benefit over USB flash drives, as the latter sticks out of the device, and the user would need to be cautious not to bump it while transporting the device, which could damage the USB port. Memory cards have a unified shape and do not reserve a USB port when inserted into a computer's dedicated card slot.

Since late 2009, newer Apple computers with installed SD card readers have been able to boot in macOS from SD storage devices, when properly formatted to Mac OS Extended file format and the default partition table set to GUID Partition Table.^[152]

SD cards are increasing in usage and popularity among owners of vintage computers like 8-bit Atari. For example SIO2SD (SIO is an Atari port for connecting external devices) is used nowadays. Software for an 8-bit Atari may be included on one SD card that may have less than 4–8 GB of disk size (2019).^[153]

Embedded systems

A shield (daughterboard) that gives Arduino prototyping microprocessors access to SD cards

In 2008, the SDA specified Embedded SD, "leverag[ing] well-known SD standards" to enable non-removable SD-style devices on printed circuit boards.^[154] However this standard was not adopted by the market while the MMC standard became the de facto standard for embedded systems. SanDisk provides such embedded memory components under the iNAND brand.^[155]

Most modern microcontrollers have built-in SPI logic that can interface to an SD card operating in its SPI mode, providing non-volatile storage. Even if a microcontroller lacks the SPI feature, the feature can be emulated by bit banging. For example, a home-brew hack combines spare General Purpose Input/Output (GPIO) pins of the processor of the Linksys WRT54G router with MMC support code from the Linux kernel.^[156] This technique can achieve throughput of up to 1.6 Mbit/s.

Music distribution

Prerecorded microSDs have been used to commercialize music under the brands slotMusic and slotRadio by SanDisk and MQS by Astell & Kern.

Physical size

The SD card specification defines three physical sizes. The SD and SDHC families are available in all three sizes, but the SDXC and SDUC families are not available in the mini size, and the SDIO family is not available in the micro size. Smaller cards are usable in larger slots through use of a passive adapter.

Standard

Size comparison of families: SD (blue), miniSD (green), microSD (red)

• SD (SDSC), SDHC, SDXC, SDIO, SDUC
• 32 mm × 24 mm × 2.1 mm (1+17⁄64 in × 15⁄16 in × 5⁄64 in)
• 32 mm × 24 mm × 1.4 mm (1+17⁄64 in × 15⁄16 in × 1⁄16 in) (as thin as MMC) for Thin SD (rare)

Transfer modes

Cards may support various combinations of the following bus types and transfer modes. The SPI bus mode and one-bit SD bus mode are mandatory for all SD families, as explained in the next section. Once the host device and the SD card negotiate a bus interface mode, the usage of the numbered pins is the same for all card sizes.

• SPI bus mode: Serial Peripheral Interface Bus is primarily used by embedded microcontrollers. This bus type supports only a 3.3-volt interface. This is the only bus type that does not require a host license.
• One-bit SD bus mode: Separate command and data channels and a proprietary transfer format.
• Four-bit SD bus mode: Uses extra pins plus some reassigned pins. This is the same protocol as the one-bit SD bus mode which uses one command and four data lines for faster data transfer. All SD cards support this mode. UHS-I and UHS-II require this bus type.
• Two differential lines SD UHS-II mode: Uses two low-voltage differential signalling interfaces to transfer commands and data. UHS-II cards include this interface in addition to the SD bus modes.

The physical interface comprises 9 pins, except that the miniSD card adds two unconnected pins in the center and the microSD card omits one of the two V_SS (Ground) pins.^[158]

Official pin numbers for each card type (top to bottom): MMC, SD, miniSD, microSD. This shows the evolution from the older MMC, on which SD is based. NOTE: This drawing does not show 8 new UHS-II contacts that were added in spec 4.0.

Notes:

1. Direction is relative to card. I = Input, O = Output.
2. PP = Push-Pull logic, OD = Open-Drain logic.
3. S = Power Supply, NC = Not Connected (or logical high).

Interface

Inside a 512 MB SD card: NAND flash chip that holds the data (bottom) and SD controller (top)

Inside a 2 GB SD card: two NAND flash chips (top and middle), SD controller chip (bottom)

Inside a 16 GB SDHC card

Power consumption

The power consumption of SD cards varies by its speed mode, manufacturer and model.

During transfer it may be in the range of 66–330 mW (20–100 mA at a supply voltage of 3.3 V). Specifications from TwinMOS Technologies list a maximum of 149 mW (45 mA) during transfer. Toshiba lists 264–330 mW (80–100 mA).^[164] Standby current is much lower, less than 0.2 mA for one 2006 microSD card.^[165] If there is data transfer for significant periods, battery life may be reduced noticeably; for reference, the capacity of smartphone batteries is typically around 6 Wh (Samsung Galaxy S2: 1650 mAh @ 3.7 V).

Modern UHS-II cards can consume up to 2.88 W, if the host device supports bus speed mode SDR104 or UHS-II. Minimum power consumption in the case of a UHS-II host is 720 mW.

SDSC cards above 1 GB

4 GB SDSC card

SD version 1.00 assumed 512 bytes per block. This permitted SDSC cards up to 4,096 × 512 × 512 B = 1 GB.^{[lower-alpha 4]}

Version 1.01 let an SDSC card use a 4-bit field to indicate 1,024 or 2,048 bytes per block instead.^[85] Doing so enabled cards with 2 GB and 4 GB capacity, such as the Transcend 4 GB SD card, the Memorette 4 GB SD card and the Hoco 4 GB microSD card.

Storage capacity calculations

The format of the Card-Specific Data (CSD) register changed between version 1 (SDSC) and version 2.0 (which defines SDHC and SDXC).

Capacity = (C_SIZE + 1) × 2(C_SIZE_MULT + READ_BL_LEN + 2)
where
  0 ≤ C_SIZE ≤ 4095,
  0 ≤ C_SIZE_MULT ≤ 7,
  READ_BL_LEN is 9 (for 512 bytes/sector) or 10 (for 1024 bytes/sector)

Capacity = (C_SIZE + 1) × 524288
where for SDHC  
  4112 ≤ C_SIZE ≤ 65375  
  ≈2 GB ≤ Capacity ≤ ≈32 GB
where for SDXC 
  65535 ≤ C_SIZE
  ≈32 GB ≤ Capacity ≤ 2 TB