Statistical channel state information

If the receiver knows the channel matrix and the transmitter has statistical information, eigenbeamforming is known to achieve the MIMO channel capacity.^[5] In this approach, the transmitter emits multiple streams in eigendirections of the channel covariance matrix.

Full channel state information

If the channel matrix is completely known, singular value decomposition (SVD) precoding is known to achieve the MIMO channel capacity.^[6] In this approach, the channel matrix is diagonalized by taking an SVD and removing the two unitary matrices through pre- and post-multiplication at the transmitter and receiver, respectively. Then, one data stream per singular value can be transmitted (with appropriate power loading) without creating any interference whatsoever.

Linear precoding with full channel state information

This suboptimal approach cannot achieve the weighted sum rate, but it can still maximize the weighted sum performance (or some other metric of achievable rates under linear precoding). The optimal linear precoding does not have any closed-form expression, but it takes the form of a weighted MMSE precoding for single-antenna receivers.^[3] The precoding weights for a given user are selected to maximize a ratio between the signal gain at this user and the interference generated at other users (with some weights) plus noise. Thus, precoding can be interpreted as finding the optimal balance between achieving strong signal gain and limiting inter-user interference.^[11]

Finding the optimal weighted MMSE precoding is difficult, leading to approximate approaches where the weights are selected heuristically. A common approach is to concentrate on either the numerator or the denominator of the mentioned ratio; that is, maximum ratio transmission (MRT)^[8] and zero-forcing (ZF)^[12] precoding. MRT only maximizes the signal gain at the intended user. MRT is close-to-optimal in noise-limited systems, where the inter-user interference is negligible compared to the noise. ZF precoding aims at nulling the inter-user interference, at the expense of losing some signal gain. ZF precoding can achieve a performance close to the sum capacity when the number of users is large or the system is interference-limited (i.e., the noise is weak compared to the interference). A balance between MRT and ZF is obtained by the so-called regularized zero-forcing^[13] (also known as signal-to-leakage-and-interference ratio (SLNR) beamforming^[14] and transmit Wiener filtering^[9]) All of these heuristic approaches can also be applied to receivers that have multiple antennas.^[9][13][14]

Also for multiuser MIMO system setup, another approach has been used to reformulate the weighted sum rate optimization problem to a weighted sum MSE problem with additional optimization MSE weights for each symbol in.^[15] However, still this work is not able to solve this problem optimally (i.e., its solution is suboptimal). On the other hand, duality approach also considered in ^[16] and ^[17] to get sub-optimal solution for weighted sum rate optimization.

Note that the optimal linear precoding can be computed using monotonic optimization algorithms,^[18][19] but the computational complexity scales exponentially fast with the number of users. These algorithms are therefore only useful for benchmarking in small systems.

Linear precoding with limited channel state information

In practice, the channel state information is limited at the transmitter due to estimation errors and quantization. Inaccurate channel knowledge may result in significant loss of system throughput, as the interference between the multiplexed streams cannot be completely controlled. In closed-loop systems, the feedback capabilities decide which precoding strategies that are feasible. Each receiver can either feedback a quantized version of its complete channel knowledge or focus on certain critical performance indicators (e.g., the channel gain).

If the complete channel knowledge is fed back with good accuracy, then one can use strategies designed for having full channel knowledge with minor performance degradation. Zero-forcing precoding may even achieve the full multiplexing gain, but only provided that the accuracy of the channel feedback increases linearly with signal-to-noise ratio (in dB).^[12] Quantization and feedback of channel state information is based on vector quantization, and codebooks based on Grassmannian line packing have shown good performance.^[20]

Other precoding strategies have been developed for the case with very low channel feedback rates. Random beamforming^[10] (or opportunistic beamforming^[21]) was proposed as a simple way of achieving good performance that scales like the sum capacity when the number of receivers is large. In this suboptimal strategy, a set of beamforming directions are selected randomly and users feed back a few bits to tell the transmitter which beam gives the best performance and what rate they can support using it. When the number of users is large, it is likely that each random beamforming weight will provide good performance for some user.

In spatially correlated environments, the long-term channel statistics can be combined with low-rate feedback to perform multi-user precoding.^[22] As spatially correlated statistics contain much directional information, it is only necessary for users to feed back their current channel gain to achieve reasonable channel knowledge. As the beamforming weights are selected from the statistics, and not randomly, this approach outperforms random beamforming under strong spatial correlation.^[23]

In multiuser MIMO systems where the number of users are higher than the number of transmit antennas, a multiuser diversity can be achieved by performing user scheduling before applying zero-forcing beamforming. Multiuser diversity is a form of selection diversity among users, the base station can schedule its transmission to those users with favorable channel fading conditions to improve the system throughput. In order to achieve multiuser diversity and apply zero-forcing precoding, the CSI of all users are required at the base station. However, the amount of overall feedback information increases with the number of users. Therefore, it is important to perform a user selection at the receiver to determine the users which feed back their quantized CSI to the transmitter based on a pre-defined threshold. ^[24]

DPC or DPC-like nonlinear precoding

Dirty paper coding is a coding technique that pre-cancels known interference without power penalty. Only the transmitter needs to know this interference, but full channel state information is required everywhere to achieve the weighted sum capacity.^[7] This category includes Costa precoding,^[25] Tomlinson-Harashima precoding^[26][27] and the vector perturbation technique.^[28]

Description of Point-to-Point MIMO

The standard narrowband, slowly fading channel model for point-to-point (single-user) MIMO communication is described in the page on MIMO communication.

Description of Multi-user MIMO

Consider a downlink multi-user MIMO system where a base station with ${\displaystyle N}$ transmit antennas and ${\displaystyle K}$ single-antenna users. The channel to user ${\displaystyle k}$ is described by the ${\displaystyle N\times 1}$ vector ${\displaystyle \mathbf {h} _{k}}$ of channel coefficients and its ${\displaystyle i}$th element describes the channel response between the ${\displaystyle i}$th transmit antenna and the receive antenna. The input-output relationship can be described as

${\displaystyle y_{k}=\mathbf {h} _{k}^{H}\mathbf {x} +n_{k},\quad k=1,2,\ldots ,K}$

where ${\displaystyle \mathbf {x} }$ is the ${\displaystyle N\times 1}$ transmitted vector signal, ${\displaystyle y_{k}}$ is the received signal, and ${\displaystyle n_{k}}$ is the zero-mean unit-variance noise.

Under linear precoding, the transmitted vector signal is

${\displaystyle \mathbf {x} =\sum _{i=1}^{K}\mathbf {w} _{i}s_{i},}$

where ${\displaystyle s_{i}}$ is the (normalized) data symbol and ${\displaystyle \mathbf {w} _{i}}$ is the ${\displaystyle N\times 1}$ linear precoding vector. The signal-to-interference-and-noise ratio (SINR) at user ${\displaystyle k}$ becomes

${\displaystyle {\textrm {SINR}}_{k}={\frac {|\mathbf {h} _{k}^{H}\mathbf {w} _{k}|^{2}}{\sigma _{k}^{2}+\sum _{i\neq k}|\mathbf {h} _{k}^{H}\mathbf {w} _{i}|^{2}}}}$

where ${\displaystyle \sigma _{k}^{2}}$ is the noise variance for channel to user ${\displaystyle k}$ and the corresponding achievable information rate is ${\displaystyle \log _{2}(1+{\textrm {SINR}}_{k})}$ bits per channel use. The transmission is limited by power constraints. This can, for example, be a total power constraint ${\displaystyle \sum _{i=1}^{K}\|\mathbf {w} _{i}\|^{2}\leq P}$ where ${\displaystyle P}$ is the power limit.

A common performance metric in multi-user systems is the weighted sum rate

${\displaystyle {\underset {\{\mathbf {w} _{k}\}:\sum _{i}\|\mathbf {w} _{i}\|^{2}\leq P}{\mathrm {maximize} }}\sum _{k=1}^{K}a_{k}\log _{2}(1+{\textrm {SINR}}_{k})}$

for some positive weights ${\displaystyle a_{k}}$ that represent the user priority. The weighted sum rate is maximized by weighted MMSE precoding that selects

${\displaystyle \mathbf {w} _{k}^{\textrm {W-MMSE}}={\sqrt {p_{k}}}{\frac {(\mathbf {I} +\sum _{i\neq k}q_{i}\mathbf {h} _{i}\mathbf {h} _{i}^{H})^{-1}\mathbf {h} _{k}}{\|(\mathbf {I} +\sum _{i\neq k}q_{i}\mathbf {h} _{i}\mathbf {h} _{i}^{H})^{-1}\mathbf {h} _{k}\|}}}$

for some positive coefficients ${\displaystyle q_{1},\ldots ,q_{K}}$ (related to the user weights) that satisfy ${\displaystyle \sum _{i=1}^{K}q_{i}=P}$ and ${\displaystyle p_{i}}$ is the optimal power allocation.^[11]

The suboptimal MRT approach removes the channel inversion and only selects

${\displaystyle \mathbf {w} _{k}^{\mathrm {MRT} }={\sqrt {p_{k}}}{\frac {\mathbf {h} _{k}}{\|\mathbf {h} _{k}\|}},}$

while the suboptimal ZF precoding makes sure that ${\displaystyle \mathbf {h} _{i}^{H}\mathbf {w} _{k}^{\mathrm {ZF} }=0}$ for all i ≠ k and thus the interference can be removed in the SINR expression:

${\displaystyle {\textrm {SINR}}_{k}^{\mathrm {ZF} }={\frac {|\mathbf {h} _{k}^{H}\mathbf {w} _{k}^{\mathrm {ZF} }|^{2}}{\sigma _{k}^{2}}}.}$