PICkit 1

The PICkit 1 was a rudimentary USB programmer for PIC microcontrollers, produced by Microchip Technology, the manufacturer of the PIC series of microcontrollers. It was introduced on March 31, 2003, priced at US$36.^[1]

The PICkit 1 was integrated into a demonstrator board, featuring eight LEDs, a switch, and a potentiometer. Its default program, explained in the documentation, rotates the LEDs in series. The light display's direction and speed of rotation can be changed with the button and potentiometer on the PICkit board.

PICkit 2

PICkit 2

The PICkit 2 was introduced in May 2005^[2] to replace the PICkit 1. The PICkit 2 has a separate programmer/debugger unit which plugs into the board carrying the chip to be programmed, whereas the PICkit 1 is a single unit. This makes it possible to use the programmer with a custom circuit board via an in-circuit serial programming (ICSP) header. This feature is not intended^[2] for so-called "production" programming, however.

The PICkit 2 uses an internal PIC18F2550 with FullSpeed USB. The PICkit 2 firmware allows the user to program and debug most of the 8 and 16-bit PICmicro and dsPIC members of the Microchip product line.

The PICkit 2 is open to the public, including its hardware schematic, firmware source code (in C language), and application programs (in C# language). End users and third parties can modify both the hardware and software. e.g. Linux version of PICkit 2 application software, DOS-style CMD support, etc.

The PICkit 2 has a Programmer-To-Go (PTG) feature, which enables the PIC MCU memory image to be downloaded into on-board memory (128 KB I²C EEPROM or 256 KB I²C EEPROM). Once the image has been downloaded, devices can be programmed with this memory image without a PC.

The Microchip version of PICkit 2 has 128 KB memory as standard. 256 KB memory can be accommodated by modifying the hardware or by using a third-party clone.

A 500 kHz three-channel logic analyzer and a UART tool are built into the PICkit 2. These features are not available in the PICkit 3.

Since the release of V2.61, PICkit 2 PC software now supports a maximum of 4 megabytes of memory for the programmer-to-go feature. With this modification, the PICkit 2 supports eight times as much memory as the PICkit 3. This enhancement has been contributed by Au Group Electronics and the PICkit 2 firmware is also reported to be submitted to the Microchip PICkit 2 team in the middle of March 2009.

PICkit 3

PICkit 3

In January 2009, Microchip released the PICkit 3, a variation of the PICkit 2 with the same form factor and a new translucent case. It features a faster 16-bit PIC24F processor and a wider voltage regulation range.

Both PICkit 2 and PICkit 3 have internal, switch-mode voltage regulators: from a 5 V USB supply at around 100 mA, the PICkit 2, generates 2.5 to 5 volts, and the PICkit 3 generates 2.5 to 5.5 volts. On both units, accuracy may be increased by calibrating the output with a multimeter. For some PICs, the MCLR programming voltage can be generated, at around 13 to 14 volts. This voltage is required to reprogram the flash memory.

PICkit 4

PICkit 4

In February 2018, Microchip released the PICkit 4, which supports ICSP and JTAG debugging/programming. At the time of launch, not all PIC devices are supported, but the firmware is continually being upgraded to add support for new devices.^[3]

PICkit4 also supports programming/debugging of AVR devices with UPDI/PDI/JTAG/SPI/debugWIRE interfaces by enumerating in "AVR mode" which makes its USB communication interface compatible with that of Atmel-ICE.

PICkit 5

In July 2023, Microchip released the PICkit 5. It supports ICSP and JTAG debugging/programming for Microchip devices and UPDI/PDI/JTAG/SPI/debugWIRE for AVR devices.^[4]

Visually it's almost identical to the PICkit 4 and both share a similar feature set. The only notable functional differences are the USB-C connector (instead of micro-B USB) and Bluetooth connectivity.^[5]

PICkit 2 and PICkit 3

The software for the Microchip PICkit 2 and PICkit 3 in-circuit debugger/programmers was released by Microchip in 2009 and 2012 respectively. The software is open source and not maintained by Microchip. Consequently, there is no support for modern operating systems or new PIC microcontrollers.

PICkit 3.5

PICkit3.5 is a description of a clone not made by Microchip.^[9] The device claims to offer some improvements over the PICkit 3 from MicroChip and Clones from other manufacturers.^[10]

PICkit Plus

In 2018, PICkit Plus software^[11] was released to support the newer 8-bit microcontrollers that were not supported by the original Microchip software — including, but not limited to, the 16F18xxx and 18F2xKxx ranges. The software is donateware.

The intent of PICkit Plus is to facilitate the programming of any 8-bit PIC microcontroller using the PICkit™ 2 and PICkit™ 3 (ICSP) In-Circuit Debuggers/Programmers. The software extends the life of the existing PICkit2 and PICkit3 hardware devices by allowing them to work with the newer 8-bit PIC microcontrollers.

The capabilities include:

• Three applications:

1. Updated PICkit 3 graphical interface for the PICkit3 hardware;
2. Updated PICkit 2 graphical interface for the PICkit2 hardware; and
3. A new command-line application that supports both PICkit2 and PICkit3 devices.

• New programming protocol support for new classes of Microchip's 8-bit PIC microcontrollers.
• Updated and managed 8-bit microcontroller database, to keep the software current with future microcontroller products.
• Improved user interface.
• Improved reliability (bug fixes).
• Improved help and users PDFs.
• Software is compatible with existing integrated development environment (IDE) software.
• Supports low-voltage (2v to 6v) programming (LVP), and high-voltage (9v to 12v) programming (HVP)
• Can read, write or erase program- and data memory of microcontrollers, with verification.
• Supports Windows 10, Windows 8.1, Windows 8.0, Windows 7 and Windows XP.

There are plans in the future to support MacOS and Linux.

PICkit Minus

In 2021, Finnish developer Jaakko Kairus published software called PICkitminus (PICkit-).^[12] The software is freeware.

The intent of PICkit- is to be able to program PICs using the SPI-type programming method. Some of these types of PICs (known as MSb1st) require reversing bit order, unlike regular PICs. Therefore, they cannot be programmed with the original PICkit software. The software was developed using the PICkit 3 standalone software.

Pickit2 and PICkit3 are supported on a single application. PICKit3 requires special scripting firmware.

Features:

• Supports most, if not all, 8-bit PIC microcontrollers which use ICSP
• Supports PICkit2 and PICkit3 programmers, including clones like PICkit3.5 or PK2M
• Improved auto-detection of parts
• PICkit2 supports programmer-to-go also with recent MSB1st families
• Optimized programming scripts for MSB1st families to reduce write and verify times
• Improved blank section skipping for write and verify, to further reduce programming times
• Improved operation with PICkit3 clones
• UART tool also for PICkit3.
• UART is possible to use with other software by creating a virtual COM port
• SPI FLASH device support.
• GUI software works on Windows 2000, XP, 7, 10, 11
• Command line software works on Windows XP, 7, 10, 11, Linux and MacOS
• Retains all the good features from the original Microchip PICkit2 and PICkit3 stand-alone software