Bipole 1

A 150 kV mercury arc valve in Bipole 1 of Manitoba Hydro's Radisson converter station, August 2003.
By the end of 2004 all of these mercury valves had been replaced with thyristors.

Bipole 1 runs 895 kilometres (556 mi) from Radisson to Dorsey. It was originally rated to run at a maximum potential difference of ±450 kilovolts and a maximum power of 1620 megawatts.^[5] This results in an electric current of 1800 Amperes.

Bipole 1 consists of six, 6-pulse converter groups at each end (three in series per pole), each originally rated at 150 kV DC, 1800 A.^[6] Each converter group can be bridged at the DC side with a vacuum switch. Subsequent upgrades have increased the current rating to 2000 A and the voltage rating of most equipment to 166 kV per bridge (i.e., 500 kV total), although as of January 2013 Manitoba Hydro still report that the line is operated at +463 kV/−450 kV.

When it was built between March 1971 and October 1977, mercury-arc valves were used to rectify the alternating current. These valves, supplied by English Electric,^[7] each had six anode columns in parallel and were the most powerful mercury arc valves ever built. Each of them had a weight of 10,200 kg (22,500 lb), a length of 4.57 metres (15.0 feet), a width of 2.44 metres (8.0 feet) and a height of 3.96 metres (13.0 feet). Between 1992 and 1993 the mercury arc valves of Pole 1 were replaced with thyristor valves by GEC Alsthom, increasing the maximum power and voltage of the line to its current levels. The mercury arc valves of Pole 2 were replaced later by Siemens.^[8] By the end of 2004 the last of the mercury arc valves in Pole 2 had been replaced by thyristor valves.

At both Radisson and Dorsey, the thyristor valves are situated in the same hall where the mercury arc valves originally stood. At both locations, the hall has a height of 18.29 metres (60.0 feet), a width of 22.86 metres (75.0 feet) and a length of 44.2 metres (145 feet).

Bipole 2

The Bipole 2 transmission line runs 937 kilometres (582 mi) from Henday to Dorsey. Bipole 2 can transfer a maximum power of 1800 MW at a potential of ±500 kV. Bipole 2 consists of four 12-pulse converter groups at each end (two in series per pole) and was put into service in two stages. After the first stage in 1978 the maximum power was 900 MW at 250 kV, which increased to its present figure when it was completed in 1985.^[9]

Bipole 2 crosses Nelson River at 56.459811 N 94.143273 W. There is a backup crossing of Nelson River at 56.441383 N 94.176114 W. It is not possible to directly switch the line to the backup crossing.

Unlike Bipole 1, Bipole 2 has always been equipped with thyristors. The thyristor valves, supplied by the German HVDC consortium (Siemens, AEG and Brown Boveri) used water cooling^[10] for the first time in an HVDC project. Until that time, the relatively few HVDC schemes using thyristors had used either air cooling or, as on the Cahora Bassa project supplied by the same consortium, oil-cooling. The thyristor valves were arranged in floor-mounted vertical stacks of four valves each (quadrivalves). Each valve contained 96 thyristor levels in series, with two in parallel. These were arranged in 16 thyristor modules connected in series with 8 reactor modules.

The Bipole 2 thyristor valves: Six parallel-connected pairs of thyristors in a module, with cooling piping and voltage grading capacitors.

An 1800 A 250 kV quadruple thyristor valve in Bipole 2 of the Henday Converter Station

Bipole 3

In 1996 an extreme wind effect damaged both Bipoles 1 and 2 and threatened to black out Winnipeg. Power was maintained by importing from Minnesota while the two existing Bipoles were repaired. To avoid a repetition of this event, and further improve the reliability of the power supply, Manitoba Hydro examined routes further to the west for their Bipole 3 line. The plans also include an additional converter station and feeder lines around the city. Bipole 3 construction started in 2012. The line was completed and entered service in July 2018.^[11]

The main elements of the Bipole III system are:

• Keewatinoow Converter Station, located on the Nelson River near the site of the proposed Conawapa Generating Station at 56°39′25″N 93°51′14″W / 56.65694°N 93.85389°W / 56.65694; -93.85389 (Keewatinoow Static Inverter Plant)
• A 1,324 km bipolar transmission line operating at nominally +/-500 kV, running to the West of Lake Manitoba
• Riel Converter Station, on the east side of the Winnipeg Floodway, in the Rural Municipality of Springfield at 49°51′59″N 96°56′24″W / 49.86639°N 96.94000°W / 49.86639; -96.94000 (Riel Static Inverter Plant)
• Additional 230 kV AC lines for the northern collector system.^[12]

The line uses guyed steel towers in northern stretches of the line and self-supporting steel lattice towers in the southern part. On average there will be about two structures per kilometer. Each tower carries a bundled conductor for each pole. Each pole conductor is made of three sub-conductors equivalent to 1,590 MCM ACSR. Conductors are supported by toughened glass or porcelain strain insulators with a maximum clearance to ground level of 34 meters, with a minimum of 13.2 meters at mid span and maximum conductor sag. The top of the towers carries an optical ground cable providing grounding interconnection for the towers and optical fibers for control and communication of the system.^[12]

Typically the right-of-way for the HVDC line is 66 meters, with 45 meters cleared directly below the line.

The system is capable of transmitting 2000 megawatts from the Nelson River stations to loads in the south.

Ground return electrodes

Although normally each of the lines run as bipolar systems, if a pole is shut down for maintenance or a fault, the ground return electrode is used to maintain partial capacity operation.

Bipoles 1 and 2 share a ground electrode of ring type, 305 metres (1,001 ft) in diameter, 21.9 kilometres (13.6 mi) from the Dorsey Converter Plant at 50°10′29″N 97°24′08″W / 50.17472°N 97.40222°W / 50.17472; -97.40222 (Dorsey Converter Station Ground Return Electrode). The Dorsey electrode is connected with the converter plant by two overhead lines on wooden poles, one for Bipole 1 and one for Bipole 2.

At Radisson, Bipole 1 uses a ground electrode of the same size and type as Dorsey, but only 11.2 kilometres (7.0 mi) away from the station at 56°21′22″N 94°45′17″W / 56.35611°N 94.75472°W / 56.35611; -94.75472 (Radisson Converter Station Ground Return Electrode).

Bipole 2 uses a ground electrode 548 metres (1,798 ft) in diameter, and 11.2 kilometres (7.0 mi) from the Henday Converter Station 56°26′2″N 94°13′22″W / 56.43389°N 94.22278°W / 56.43389; -94.22278 (Henday Converter Station Ground Return Electrode).

Bipole 3 has a ground electrode site near the Keewatinoow Converter Station at 56°34′56″N 93°57′02″W / 56.58222°N 93.95056°W / 56.58222; -93.95056 (Keewatinoow Ground Electrode) connected by a 30 km electrode line. At the southern Riel Converter Station, the electrode line runs about 26 km to a grounding electrode site at 49°56′12″N 96°43′01″W / 49.93667°N 96.71694°W / 49.93667; -96.71694 (Hazelridge Ground Electrode) near Hazelridge, Manitoba.

Bipole III electrode ground line north of Dugald, Manitoba.