Wheeler Ridge Compressor Station, in Kern County, California

A compressor station is a facility which helps the transportation process of natural gas from one location to another. Natural gas, while being transported through a gas pipeline, needs to be periodically pressurized at intervals of 40 to 100 miles (64 to 161 km).[1] Siting is dependent on terrain, and the number of gas wells in the vicinity. Frequent elevation changes and a greater number of gas wells will require more compressor stations.[2]

The compressor station, also called a pumping station, is the "engine" that powers a long-distance natural gas pipeline. As the name implies, the station compresses the gas (increasing its pressure) thereby providing energy to move it through the pipeline.[3] The compressor is driven by a motor fueled by some of the natural gas bled from the pipeline.

Pipeline companies install compressor stations along a pipeline route. The size of the station and the number of compressors (pumps) varies, based on the diameter of the pipe and the volume of gas to be moved. Nevertheless, the basic components of a station are similar.

Liquid Separators

As the pipeline enters the compressor station the natural gas passes through scrubbers, strainers or filter separators. These are vessels designed to remove any free liquids or dirt particles from the gas before it enters the compressors. Though the pipeline is carrying “dry gas,” some water and hydrocarbon liquids may condense out of the gas stream as the gas cools and moves through the pipeline.

Any liquids that may be produced are collected and stored for sale or disposal. A piping system directs the gas from the separators to the gas compressor for compression.

Prime Movers

Mobile compressor station produced by the Ufa Compressor Factory on a KamAZ-63501 chassis

There are three commonly used types of engines that drive the compressors and are known as "prime movers":[3]

  • Turbine / Centrifugal Compressor uses a natural gas-fired turbine to turn a centrifugal compressor. The centrifugal compressor is similar to a large fan inside a case, which pumps the gas as the fan turns. A small portion of natural gas from the pipeline is burned to power the turbine.
  • Electric Motor/Centrifugal Compressor uses a centrifugal compressor driven by a high voltage electric motor. An electrified compressor may still require an air permit,[4] as regulations vary by state an applicability analysis should be conducted whenever a compressor station will be constructed. A highly reliable source of electric power must be available and near the station.
  • Reciprocating Engine/Reciprocating Compressor uses a large piston engine resembling an automobile engine, only much larger. Commonly known as “recips,” these engines are fueled by natural gas from the pipeline. Reciprocating pistons, located in cylinder cases on the side of the unit, compress the natural gas. The compressor pistons and the power pistons are connected to a common crankshaft. The advantage of reciprocating compressors is that the volume of gas pushed through the pipeline can be adjusted incrementally to meet small changes in customer demand.

See also

References

  1. ↑ "The Transportation of Natural Gas". NaturalGas.org. Natural Gas Supply Association. 2013-09-20. Archived from the original on 2011-01-01. Retrieved 2020-06-26.
  2. ↑ Kurz, Rainer; Lubomirsky, Matt; Brun, Klaus (13 August 2018). "Gas Compressor Station Economic Optimization". International Journal of Rotating Machinery. 2012: 1–9. doi:10.1155/2012/715017.
  3. 1 2 "INGAA Website - Compressor Stations". www.ingaa.org. Archived from the original on 2019-12-25. Retrieved 2012-09-04.
  4. ↑ "Archived copy" (PDF). Archived from the original (PDF) on 2014-08-10. Retrieved 2014-12-15.{{cite web}}: CS1 maint: archived copy as title (link)
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.