Hyppe Max Air 5000 Teardown

Written By: ShellingRook27
Published: 06/06/23
  • Comments: 0

Hyppe Max Air 5000 Teardown

Published: 06/06/23

Teardown

Introduction

I found this device on the ground and decided to take it apart. These types of disposable devices are not made to be disassembled.

  1. NIgWoLm5b6EMxIfO
    NIgWoLm5b6EMxIfO
    LUBZUHPSkJeCuOQF
    CuHWSaenaWQqGLNA

    • Remove rubber bumper

  2. ycDgvFMeCdo41gcQ

    • The plastic shell is ultrasonically welded shut

    • This is due to the disposable nature of the device

    • I don't have images of the removal process but I used a razor to lightly go along the seam and then spit it apart with a spudger

  3. FNAxjCWJvLhJa1fe
    FNAxjCWJvLhJa1fe
    mSEqWPxNZpmluYrJ

    • Lift upwards

  4. ipQ1AFwAfdTSRIcw
    ipQ1AFwAfdTSRIcw
    cRMrBKVfYCUlKVpB
    H4iMABTW5ynZNpW3

    • Lift up the battery

    • 3.7V 1.85Wh

  5. u6pluVufFfSX2fTA
    u6pluVufFfSX2fTA
    JUupOFjGVlLpuplQ

    • Use the point part of the spudger to get under the port and pry it up

  6. UtmULlBCaOUVEqIu
    UtmULlBCaOUVEqIu
    FNekFhJtBtivyvkH

    • Remove the PH00 screw

  7. vQc1QPZbgGIpAPjt
    vQc1QPZbgGIpAPjt
    VsigApS3PkyOcXnb
    aP1FT4XSdWC25kkY

    • Use the ponty end of the spudger to lift up the airflow sensor

  8. A1B3FTPVW6Kw2eTL
    A1B3FTPVW6Kw2eTL
    XH3DyUm3WnVI5UuR

    • Use flat end of spudger to pry out chamber

    • Everything should now be come out of the plastic housing

  9. dC6A3RXNDGpYOLMA
    dC6A3RXNDGpYOLMA
    ALCD2NELumT4WRGw

    • Some close up images of the PCB

  10. DHGKkLjALjITQoNo
    DHGKkLjALjITQoNo
    thgFUjXHrNGHiZI6
    NOB2byWK46X4wdOk

    • Pull on the heater and it should just pop out

    • It's interesting to see that the heater geometry is just a mesh

  11. hONwwTkVRYXRrT1r
    hONwwTkVRYXRrT1r
    deGHi3HEtgAreqXu

    • Use the spudger to pop off the rubber lid of the chamber

  12. hwGY2HPMPAfLtLQm
    hwGY2HPMPAfLtLQm
    LXWcZCoxg1XULveA

    • Pull out the foam-like material

  13. rMHochoNqh6qgfev
    rMHochoNqh6qgfev
    LvL5FAAa2j3FSkpc
    gMbM3vnMdcHxE6EL

    • Use spudger to push out core

    • The heating element sits inside the sleeve. There is some wicking material on the inside to bring the nicotine liquid close to the heating mesh.

Author

ShellingRook27

Member since: 21/08/19

1885 Reputation

0 comments