WowWee CHiP Robot Dog Ear Replacement

Written By: Joseph Dantes
  • Comments: 5
WowWee CHiP Robot Dog Ear Replacement

Difficulty

Difficult

Steps

9

Time Required

10 - 20 minutes

Introduction

  1. iOX2vmPMYVk2CdYx

    • Place CHiP on its back so that its stomach is facing you.

  2. yQs2QsZmwp1mLHUk
    yQs2QsZmwp1mLHUk
    AWhBjOFvrBAmMOGC

    • There are three small hex screws connecting the battery to CHiP. Remove all screws with a hex screwdriver and remove battery casing.

    Cant get the eyes to lite up, suggestions?

    Daniel peters -

  3. cwMaiURZITZSligQ
    cwMaiURZITZSligQ
    5YX2SDYbgYjGTtyM

    • Once the top face of the battery is off, you will see a small rectangular box that the batteries are inside. There are 4 Phillips head screws in the box. Remove all screws with a Phillips head screwdriver.

    what is the purpose for removing the battery if you cannot buy a new one?

    v scigliano -

    I need a new batties in my chip dog. Please tell me we're can u get it from and bed stand

    janie alexander -

  4. CkAiFU1BhmDZU4kU
    CkAiFU1BhmDZU4kU
    5iHWtXr21c5JJwn2
    TsEqpBGlgeEpMYTt

    • Once the battery is removed from body, the battery should be connected by a red and black wire. There is a red rectangular connector that easily pulls apart. Pull apart the red rectangular connector.

    where i find this battery

    Abodi Jml -

  5. jJCGcXaYqaWjovF4
    jJCGcXaYqaWjovF4
    qWmGQPe5RcGTluCA

    • Remove the 4 Phillips screws shown.

  6. xJBUGSO3g6SNICUA
    xJBUGSO3g6SNICUA
    Hva4fRLDahkcEgLa
    OTe4ObxxhWLMeMbW

    • Pull up top part of toy and remove the connecting wires.

    • Unscrew the 2 Phillips head screws. CHiP should be viewed as seen in the third picture.

  7. di5MePONDpPDSBbo
    di5MePONDpPDSBbo
    lkcDaqkoqwCaPLRL
    ClHXqcQiwMA2xLMM

    • Remove the 4 Phillips screws to separate the head from the body.

  8. IiwWTrZ3uOea5fWy
    IiwWTrZ3uOea5fWy
    5wrCkhSEwTBsttEH

    • Remove the 4 Phillips screws on back of the head, and pull off the casing for the back of the head.

  9. 2YaOfAxsrf6HsEpv
    2YaOfAxsrf6HsEpv
    p66BQPNioIH3sYIm
    n6PYGuZ25hWjRE5e

    • Unscrew the screw on the ear with a Phillips screwdriver, and pull off the plastic connector. Remove the ear from head.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Joseph Dantes

Member since: 02/10/18

514 Reputation

One comment

It’s almost a disassembly, probably quite hard to do. I did disassemble a MiPosaur, but some parts broke off. (!!!)

Michael Deitz -