Whirlpool WED87HED Dryer Drum Light Replacement

Written By: Bill Gilbert
  • Comments: 2
Whirlpool WED87HED Dryer Drum Light Replacement

Difficulty

Moderate

Steps

13

Time Required

2 - 3 hours

Introduction

Use this guide to replace the LED drum light module on your Whirlpool Duet WED87HED Dryer.

Obviously, the drum light lights the inside of your dryer's drum. When it fails, it is inconvenient to check the clothes in the dryer.

  1. cRUlfkgf2YwoDST3

    • Before you begin your repair, unplug your dryer.

    • Your power cord may have four prongs rather than three. The additional prong is a ground connection.

  2. u4WTU4KTBjf1GgPm
    u4WTU4KTBjf1GgPm
    KmGeNIaHMQTiHSWW
    UyNbTg6t3WxLV6FM

    • Throughout this guide, keep track of each screw and reinstall it exactly where it came from.

    • Use a 5/16 inch nut driver to remove the two 15.7 mm-long screws securing the top panel to the rear panel bracket.

  3. gbDdHJLNo1Iiq3Y1
    gbDdHJLNo1Iiq3Y1
    vxW1WX6cffbgMuaD

    • Grasp the top and slide it 1/2 to 1 inch toward the rear of the machine.

  4. 2iNpUqjOIuDIiEQU
    2iNpUqjOIuDIiEQU
    IkW1XSsjMSmLOsT2

    • Lift the top panel upward to separate it from the chassis.

    • Remove the top panel from the machine.

  5. 4EqwYWjHdXpSDP2P
    4EqwYWjHdXpSDP2P
    I5XdQIMZQChnl4Ap

    • Disconnect the control panel cable from the main board.

  6. O21IMM2KKfDgSXgW
    O21IMM2KKfDgSXgW
    2i3v6ir4JGoNnvAC

    • Disconnect the drum light connector.

  7. vgpvSUy3LVl3MKa2
    vgpvSUy3LVl3MKa2
    5KH3EZG4GCmRwFVH

    • Use a 1/4 inch nut driver to remove the two 16.3 mm‑long sheet metal screws located at each end of the control panel.

  8. oZUJsARu4qoKMFBq
    oZUJsARu4qoKMFBq
    OQBZEtdPmGqahirE
    kBuvEfxxfEZJiHPk

    • Lift the control panel up and tilt it away from the chassis to remove it.

    • Make sure to thread the cable through the hole in the chassis.

    • During reassembly, thread the cable through its proper hole before reinstalling the control panel.

  9. V2co3pYWneoWa61J
    V2co3pYWneoWa61J
    VUqqRMDJjqT2Ai4u
    VwHKBcRPmb1AUmwD

    • Use a small flat blade screwdriver or a spudger to unlatch both sides of the door switch connector.

    • Unplug the connector.

    Could this use a locator shot to show where on the back of the control panel it's located?

    Austin Blakely -

    It isn't located on the control panel, it is near the side of the dryer cabinet, kind of tucked under the top rim of the cabinet. Thanks for the suggestion, and hope this helps to clarify.

    Bill Gilbert -

  10. QePkFLH1cNs1yBsK
    QePkFLH1cNs1yBsK
    NLcIt6rSmqBg22gl

    • Use a 1/4 inch nut driver to remove the three upper front panel 16.4 mm-long sheet metal screws.

    • Tilt the machine backwards and prop it securely, or have a friend hold it.

    • Use a 1/4 inch nut driver to remove the four sheet metal screws on the bottom edge of the panel:

    • Two 16.4 mm screws

    • Two 13 mm screws

  11. dWOkVNOZkDNLaBf6

    • Use a Phillips driver to remove the two 15.8 mm‑long screws inside the door area below the drum opening.

  12. sdiCf4sNOddWCGtb
    sdiCf4sNOddWCGtb
    1yQ6y3WfZGi4oZSD
    m1XlPkKMN2aslONt

    • The panel is heavy and awkward. You may want to have a friend help you with this step.

    • Pull the bottom of the panel away from the chassis about two to three inches.

    • Lift the front panel off the small tabs on the chassis near the top of the panel and remove it.

    • Make sure you don't snag the door switch wire harness as you remove the panel.

  13. LtJKJuI2tOJCXPfR
    LtJKJuI2tOJCXPfR
    cSxpmMYRJQKdRl1J
    sXfSnbwB4RitUuaN

    • Release the drum light module by pressing in on the tabs on the side of the module

    • Push the module through the mounting hole in the front bulkhead and into the drum.

    • Feed the wiring harness through the mounting hole and remove the module and harness from the dryer.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Ask our Answers community for help.

Author

Bill Gilbert

Member since: 30/06/22

34697 Reputation

0 comments