Sony Cyber-shot DSC-T1 Motherboard Assembly Replacement

Written By: iDeleted
  • Comments: 0
Sony Cyber-shot DSC-T1 Motherboard Assembly Replacement

Difficulty

Easy

Steps

11

Time Required

5 - 10 minutes

Introduction

This guide gives step-by-step instructions on getting to the main internal component of the Cyber-shot DSC-T1 and then specifies how to detach them from the camera.

  1. LIqAO2axT5tQyEZk
    LIqAO2axT5tQyEZk
    wv5tqGMYrQIr3KSd

    • Locate the battery door at the bottom of the camera.

    • Press down on the door and slide it back. The door will pop open.

  2. 6FYuZBMbTJ2YZPWl

    • Remove the battery from the door that you opened in the previous step.

  3. lVLDWTNZSPK3otA6
    lVLDWTNZSPK3otA6
    gfCyPgT2woJ3yyHj
    NVu4BYsuyORP2jPH

    • There are two screws on the left and right sides of the camera, and two screws on the bottom.

    • Use a PH00 screwdriver and remove the six 2.9mm screws.

  4. SaZIDW2GWVxApNkf
    SaZIDW2GWVxApNkf
    f2NIGkQgvhoSkBAD

    • Use hands to gently pry the front casing away from the camera.

  5. i6vSVy1JEKvMYUIm
    i6vSVy1JEKvMYUIm
    CAhxo3XYPqF1sGg2

    • Use the tip of a spudger to flip up the tab on the ZIF connector securing the motherboard ribbon cable.

    • The second picture shows what these tabs look like in their open positions.

  6. PcCRQm5ugiUUh45Y

    • Grasp the CCD Sensor Module and remove it.

  7. OMuS2FKiCv45IjMw
    OMuS2FKiCv45IjMw
    vH34LNowFErLpqgp
    keTowEBh6CJRGyqf

    • This camera houses a very strong capacitor (the black cylinder). Avoid touching anything around the two wires coming out of the top. Doing so will risk serious electric shock.

    • Carefully disengage the internal components from the casing by lifting at the bottom end and giving a gentle tug.

    • The components are still connected to the casing via cables, but they are much more maneuverable.

    • The flash module is shown on the right hand side.

  8. LxbCn22XZxITggXb
    LxbCn22XZxITggXb
    AneXMXOpkbyG1Ino

    • Use the tip of a spudger to flip up the tab on the ZIF connecter securing the motherboard ribbon cable.

    • Grasp the flash module by the bottom and remove it.

  9. EM1deYeKucEKKHLb
    EM1deYeKucEKKHLb
    IRtC1Yf2EgaqOHHU

    • Use tweezers to slide the white piece on the back of the back cover to the right.

    • This will dislodge the white piece, allowing you to remove it from the back cover.

  10. 6XnmE2DRlydv5AXr

    • Use the tip of a spudger to flip up the tab on the ZIF connector securing the motherboard ribbon cable.

    • Remove the ribbon cables from these two ZIF connectors.

  11. hlu534DfP6kpAjqN
    hlu534DfP6kpAjqN
    UTp34cpG6uYd1rOd

    • Lift the motherboard assembly up and rotate it so you can easily see where the internals connect to the back cover.

    • Remove the ZIF connectors from the clamp on the left end of the top piece.

    • The motherboard assembly is now separated from the back cover.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

iDeleted

Member since: 07/07/10

2101 Reputation

0 comments