Samsung NX Mini Sensor Replacement

Written By: Kelsea Weber
  • Comments: 3
Samsung NX Mini Sensor Replacement

Difficulty

Moderate

Steps

14

Time Required

No estimate

Introduction

This guide will show you how to access the sensor for cleaning or necessary repairs.

  1. psgCIinb2HQMroHV
    psgCIinb2HQMroHV
    6yv6OFRTRWGjJuDq
    LZkXwqCYcOK1XgtX

    • Orient the camera so the button panel and LCD are facing you.

    • Use a spudger or fingernail to open the battery compartment on the right side of the camera.

  2. NOJqRWLyWWHfIedp
    NOJqRWLyWWHfIedp
    PGw5WQLbd5UsU1ZT

    • Push the blue trapdoor to the left to release the battery, and remove the battery.

    • There is no battery shown in this photo.

    my battery is stuck, is there a manual release button or a way to remove the battery safely?

    beat70 -

  3. usF2HdXjipSkAu65

    • Use a Phillips #00 screwdriver to remove the 4 mm screw inside the battery compartment.

  4. FBhJCXxOCVoKTGgA

    • Remove the 4 mm Phillips #00 screw hiding in the external flash port.

    You don't show us how to remove the top plate

    Bev Curran -

  5. RQypSEK2pdXYyDFf

    • Remove the four 5 mm Phillips #00 screws from the lens assembly.

  6. 52UiRHqVkOYpBNq3

    • Remove the metal lens mount by hand or with tweezers.

    • Be careful not to touch the sensor in the center of the lens assembly.

  7. fuT3A4bYWYT26OFe

    • Use tweezers to remove the inner metal ring.

  8. n3eyKKDHKE1x6WVH

    • Use a Phillips #00 screwdriver to remove the three 4 mm screws from the bottom of the case.

  9. lhXCW5uEdZpJbVWT
    lhXCW5uEdZpJbVWT
    HYEglwV2lN5kAHBD

    • Use your hands to slowly pull the front casing away from the camera.

    • The case is attached with multiple clips that may make a cracking noise as you pull it away from the camera.

  10. 5bxPsdobXUhXKRG2
    5bxPsdobXUhXKRG2
    LeBurhyDnv546y4G
    w4jU2XYShyWsFPjy

    • Gently flip the sensor cover back to expose the screw attaching the sensor cover to the ribbon cable.

    • Use a Phillips #00 screwdriver to remove the 3 mm screw from the sensor cover.

    • Use tweezers to remove the metal contact cover. Be sure to carefully remove the cover so the gold contacts remain in place.

    • The gold lens contacts lying beneath the ribbon cable become loose when the screw and contact cover are removed.

  11. OAgp2SpqopONw5nV
    OAgp2SpqopONw5nV
    O6GLTONJMbJMiDjP

    • Remove the four 4 mm Phillips #00 screws holding the sensor mount in place.

  12. n1EoBerVgoxK5nKQ
    n1EoBerVgoxK5nKQ
    saZACwfTUYYCVJji
    XCqZmVyZQmvHGwpB

    • Remove the four 4 mm Phillips #00 screws securing the battery compartment to the mother board.

    • Remove the battery compartment.

  13. BWBfAHN2uTvO12Nn
    BWBfAHN2uTvO12Nn
    JlkgIVtduVg4jcJi

    • Use a spudger to disconnect the ribbon cable connecting the image sensor to the motherboard.

  14. TSGKI1XrLKOSBQoc

    • Gently remove the sensor mount from the camera case.

Conclusion

To reassemble your camera, follow these instructions in reverse order.

Author

Kelsea Weber

Member since: 12/11/15

20191 Reputation

One comment

Hello,

I need to know the exact dimensions of the IR-cut filter in the Samsung NX Mini camera, which should be just above the sensor. Could you possibly give me that information? I need that because I’d like to modify my NX Mini camera and change it into an infrared camera. I have to cut an infrared filter in the right size, before the disassembly of the camera.

Thank you!

Siamak ADN -