Introduction

This guide will demonstrate how to remove the disk reader of a Samsung BD-F5700 Blue Ray Reader correctly for replacement. This guide will be useful if the disk reader is not working. Before beginning make sure the device is unplugged and off. There are many fragile parts in the disk reader so handle with caution and avoid using metal tools on the interior.

  1. UxpE1BujTiXyYcIB
    UxpE1BujTiXyYcIB
    FDwftj4SjflbaYdJ
    nhXavMgdBmQAEtkh
    • Use Phillips 0 Screwdriver to remove two (2), 10 mm rear screws.

    • Use the iFixit opening tool to help separate the top plastic casing from the bottom metal casing.

    • When opening the device, be careful to not damage the ribbon cable circled in image 3.

  2. SRQIx4McCx44RLtk
    SRQIx4McCx44RLtk
    LBGyfA2yVO4MFQRH
    taVINytMnG1y4Vjd
    • Use Phillips 0 screwdriver to remove two (2), 10 mm screws from the plastic cover.

    • Remove plastic cover from board.

  3. n3YdBSRcVi5UWoCB
    n3YdBSRcVi5UWoCB
    RerJVmFIUjHRIodr
    • Pull upward on back of the black and white wire to dislocate the black tab piece from device.

    • To remove the cord from the device entirely, press on the white tab in the device and gently pull.

  4. oRcpbSZg5uCnyBSi
    • Insert the iFixit Opening tool into the black tab on the power cord, and use leverage to open the black tab.

    • Pull the tab off the wire so that it can be placed on the replacement cord.

  5. cl6fmRQtwdkkqvCu
    cl6fmRQtwdkkqvCu
    S3lBeCYB4f3w2bKD
    VVWIuAYtNLAsUP6a
    • Firmly grip the hard plastic tab attached to the base and pull upwards.

    • It is important to not tear the ribbon cables.

  6. V2XtZQSV1LVVCwki
    V2XtZQSV1LVVCwki
    KRyJBgH2pnUSRmsi
    • Remove the two 7mm screws with a Phillips #1 screwdriver.

  7. wChlRLdiu6EfMJyM
    wChlRLdiu6EfMJyM
    cVpmvsAXNokNwfNI
    TlBkgVaJASNQEV2p
    • Pinch both tabs on the side of the disc tray, push towards the front, and lift the disc tray out to remove.

  8. EyGPINZL3pVqnS2t
    EyGPINZL3pVqnS2t
    LpWhFDd2ETFKwwO3
    p3No5LPd4XrQWxYI
    • Flip up the black locking tab on the ZIF connector.

  9. cYtOZZlUWLCgKdsI
    cYtOZZlUWLCgKdsI
    Y4yUDaPDiUJIHR6c
    jNIwyJRguNPjoLBc
    • Remove the 10 mm screw using a Phillips #1 screwdriver.

    • Remove the small metal bar by pulling it outwards.

  10. McGb3EGXQZZSWoeG
    McGb3EGXQZZSWoeG
    6gyocHrjqhNMPmeT
    • Flip the disc tray over so the laser points downward.

    • Pull the disc reader out of the disc tray.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Livan Perez

Member since: 15/02/18

303 Reputation

0 comments