LG G Watch R Power Button

Written By: Westley Courchene
  • Comments: 10
LG G Watch R Power Button

Difficulty

Moderate

Steps

9

Time Required

2 minutes

Introduction

Removing the power button might be useful when attempting to clean the device.

  1. ZlkfDC3HTOI1ApbI
    ZlkfDC3HTOI1ApbI
    gHJaG6dgEMk13VNk

    • Power off your watch before disassembling it.

    • Place the watch upside down on a hard surface so that its back case is facing upright.

    • Use a T4 Torx Star screwdriver to remove the four 4.0 mm Torx screws from the corners of the back case.

    So i bought a torx t5…but it is tooo big. It must br torx t4

    Jetze Kooistra -

    I think I have damaged one of the screw heads while trying to unscrew the back of the watch.

    I used the Torx T4… but the screw was covered in quite a bit of rust. Now the Torx T4 can’t get a grip.

    What should I do? (Can anything be done?)

    John Maher -

    Yea take a tiny file or a tiny Dremel attachment and carve a flat head groove in the head just enough so where you can use a flat head to get it

    Andrew L rambeaut -

    Thank you for good instructions! Saved me for 300€ (don’t have to buy a new wacth) ?

    Ernst Kranke -

  2. 2YVX46lkVCsyyj3u

    • Use a plastic opening tool to pry open the back case from both sides of the watch.

  3. Us6TrbLowWLSEs6Y

    • Remove the back case.

  4. oJFRPNq6B5wmSEMS
    oJFRPNq6B5wmSEMS
    PV1VDkENxGFZWVDT

    • With a plastic opening tool, disconnect the four connectors on the top of the motherboard.

    Where do I buy the parts? I already have your tools.

    Marco Roman -

  5. 1mWJgarYVQPZXY5Z
    1mWJgarYVQPZXY5Z
    CGCIYUdR5WbdEGhj

    • Remove three 3.0 mm Phillips screws on the edges of the motherboard with a Phillips #000 screwdriver.

    Add colored markup to indicate location of the 3 screws.

    Patty Remmell -

    I felt like my #00 driver fit slightly better for these screws, but it probably depends on which toolkit or bit set you have.

    J Suo -

  6. lL2v1GO3SFgwcoYl

    • Grasp the edges of the motherboard and slide it slightly towards the right to remove it from its case.

  7. c5MaH1iHcwmTWCPf

    • Use a plastic opening tool to pry the battery out of the device.

    • You may need to use a stronger prying force due to the adhesive that secures the battery to the case.

    Thanks this was very helpful.

    Oseghale Akhigbe -

    Thanks for your instructions

    Gregory Francis -

    Thank you for this guide!

    Стас Шишкин -

  8. XHeJ5c2rGMhs16wV
    XHeJ5c2rGMhs16wV
    1uQcQHLvlVOgCrn3

    • Pry the battery housing from the top right corner using a spudger.

    • Once loosened, remove the battery housing.

  9. Q3ynoxI3Th6qattt
    Q3ynoxI3Th6qattt
    GHBxOriCIS5KPtNg
    VHdAqnhncIZpD1Hv

    • On the power button, locate a small grey washer on the interior side of the watch.

    • Use a pair of tweezers or another pointed object to push the washer out of its socket, and remove the power button.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Westley Courchene

Member since: 13/01/15

3410 Reputation

0 comments