Introduction

The purpose of this guide is to aid any owner of a Husqvarna Trimmer in the replacement of their gas line chamber. While the replacement process is rather straight forward and no special skills are required, it is still important for one to take caution when dealing with fuel. Be sure to use the right fuel for the Husqvarna trimmer, as all fuels are not the same. When finished or spilling occurs, stop and make sure your area and person are fully removed from the fuel before continuing on other tasks.

  1. hv64BoxPbZwhfjKX
    hv64BoxPbZwhfjKX
    Nkm212pMARtANSHk
    • Empty the gas tank and be sure to let air out for at least 48 hours.

    • Do not inhale, consume, and refill gas chamber.

  2. ggsejvBqDNWiiwpw
    • Locate the connection of the gas lines by the carburetor

  3. 2fS2bwhdYC2bJSCw
    • Detach the hoses of the gas line from the carburetor using the needle nose pliers.

    • Carefully remove line to avoid damage.

  4. 1ATeDaThXyMYfTCD
    • Use the needle nose pliers to pull the gas lines towards the top of the gas tank.

  5. ZUlEdBlOATGLfqXi
    • Pull the gas line until it is completely removed from the gas tank.

  6. MH3DZGOAgpMpxZfb
    MH3DZGOAgpMpxZfb
    UPSLtZnWa45PX2TG
    • For the second line, use a pair of sharp edge scissors to cut the remainder of the gas line from the gas tank.

    • Remove the remainder of the gas line using your hands and ensure it comes out completely leaving no gas line residue.

  7. LMBlsCNB2rlufHjW
    LMBlsCNB2rlufHjW
    fqFqLCNy2EpBinGX
    wiZCQwmQ2FaRU3TX
    • Gather filter attachment kit.

    • Gather the hoses that most closely resemble the size of the hose previously taken out.

    • Connect the filter attachment (provided in the kit) to the hose.

    • Kit contents may vary depending on brand.

  8. FdLlIUhneSUdJfRn
    • Use the metal wire, provided in the kit to guide the new tube through the hole of the gas tank.

    • Ensure that the wire comes out of the inlet of the gas tank.

  9. 6IyUpSSwar2giMnP
    • Hook the end of the gas line to the wire, so that the wire can be pulled and feed the wire through the hole.

    • To make it easy to hook the wire into the gas line, put a hole big enough for the wire to go into the line.

  10. b2jGdEcjpwISOAKu
    • Lubricate the hose using the two stroke engine oil.

    • Use the old access gas line if a dropper is difficult to locate.

  11. D2V3GbEKavWTLHMB
    • Keep pulling the gas line through the hole until the gas lines are long enough to meet the tubes on the carburetor.

    • The same rules apply when hooking up the second gas line. Just repeat steps 7 through 11.

    • Do this step with maximum precaution. The end of the gas line may tear and break.

  12. Z5BNksZLUVRLC2wr
    Z5BNksZLUVRLC2wr
    UcXLPxMsfm4YIB6D
    QLimBvCjxgdQlJYK
    • Pull out the hoses until they fit the pipes in the carburetor. Using the needle nose pliers.

    • If necessary, you may need a second pair of pliers to help get the gas line through the hole.

Conclusion

To reassemble your device, follow these instructions in reverse order.

FinalProject

Member since: 10/04/23

205 Reputation

0 comments