How to clean and maintain your Vape Mod

Written By: Jessie Smith
  • Comments: 0
How to clean and maintain your Vape Mod

Difficulty

Moderate

Steps

8

Time Required

10 - 15 minutes

Introduction

This guide will teach you how to take apart your Vape Mod completely, analyze which parts need to be cleaned, and how to correctly clean them.

  1. vyplWVs5ZFO3mJXL
    vyplWVs5ZFO3mJXL
    EY2X1NJFJBqSFJTH
    tGfchsSsFZ2WvBH1

    • Although maintenance for your Vape Mod shouldn't be dangerous, it can be messy. It is recommended to do this on top of a paper towel.

    • Start by removing the top cap of your Vape Mod.

  2. iREktJliFoBu1Vos
    iREktJliFoBu1Vos
    ZeqDjpdeL2AVAmGg
    EnktAtuwlt2MlZBO

    • Unscrew RDA (rebuildable dripping atomizer) and take it off.

  3. xoj4WNcWE4wUNVJa
    xoj4WNcWE4wUNVJa
    L6CMoDKUNUJMytyG
    bUxxGwjF4422vnZk

    • Many Vape Mods are different, you might have to take out your battery in a different way than shown.

    • At the bottom of the tube, unscrew the firing pin.

    • Take the battery out of the Vape Mod.

  4. Hbvm5aSeLFYleUgc
    Hbvm5aSeLFYleUgc
    Wv22bhJHCEghrRpB
    4Ubyjh1CBwdfPI2N

    • Inspect all of the parts that will need to be cleaned:

    • The firing pin

    • The RDA threading

    • The bottom of the inside of the tube

  5. ArJnUSaDcQKLcOya
    ArJnUSaDcQKLcOya
    r1EyZaHZypomWM2s

    • Clean the Firing pin by dipping a paper towel into hot water.

    • Carefully rotate the hot towel around the middle area, rubbing the grime away.

  6. 2xOLFs5Vk4jxfAhx
    2xOLFs5Vk4jxfAhx
    y2HboGSsDLCjlroT
    SXpqxZeSUaMIgxnv

    • Get a new paper towel wet with the hot water.

    • Clean the RDA threading by rotating the wet paper towel back and forth across it.

  7. cfjxXCgAfTmIxgdI
    cfjxXCgAfTmIxgdI
    WIRICmrCROT1YY1j
    gN1yBudmYx26YEDk

    • Get a new paper towel wet with the hot water.

    • Twist it until it can easily fit inside of the tube.

    • Use your finger or another long tool to rotate the paper towel along the sides and the bottom of the tube.

  8. UiXwOLggFaENcuMH
    UiXwOLggFaENcuMH
    1ByZpB2uZpryaCRf
    SeDltlHpfHHoNQCI

    • Put your Vape Mod back together by doing steps 1 - 2 in reverse. (Leave the mouthpiece of the top cap off).

    • Careful, firing your Vape Mod produces heat and can make the device HOT!

    • Fire your Vape Mod. If the coils are heating up, it has been fixed!

Conclusion

If your Vape Mod is still not firing, consider getting a new build.

Author

Jessie Smith

Member since: 29/09/15

677 Reputation

0 comments