How to Fix Stuck Feed Dogs on a Brother BM3700 Sewing Machine

Written By: Khalia Brown
  • Comments: 0
How to Fix Stuck Feed Dogs on a Brother BM3700 Sewing Machine

Difficulty

Moderate

Steps

10

Time Required

10 - 15 minutes

Introduction

The feed dogs are essential components of all sewing machines. As the machine operates, they oscillate in sync with the needle’s motion to move the fabric by a consistent distance with each stitch. If there is a buildup of lint, thread, and dust around the feed dogs, they may get stuck, rendering the machine unusable.

Like most sewing machines, the Brother BM3700 is susceptible to issues arising with the feed dogs due to the large amount of mechanical action that these components undergo. This guide will provide steps to resolve the issue of a stuck feed dog in a Brother BM3700 machine by clearing any debris around the feed dogs.

Before using this guide, ensure that the issue with the feed dogs is not due to problems with the electrical components of the sewing machine.

  1. tOGoBMX2EAGOkIoB

    • Ensure the power button on the machine is switched to the "off" position and the pedal is disconnected from the port at the side.

  2. VKfK3XtCodIQpTNx
    VKfK3XtCodIQpTNx
    syLHLjPKQCBP3Idy

    • Remove the needle from the machine by holding the needle while turning the needle set screw counterclockwise until the needle is loose.

    • Hold on to the needle so that it does not fall into the sewing machine.

  3. Mc4HrsdkeFRJI432
    Mc4HrsdkeFRJI432
    uqKNTyZVGxjUQFAS

    • Remove the bobbin case by gripping the bobbin case cover with two fingers and sliding it back gently.

    • Remove the presser foot by pressing the black button at the back of the presser foot lever until the attached presser foot falls off.

  4. g2dhVquBOJhcZJvt
    g2dhVquBOJhcZJvt
    6TNAQtZMqE1FAaWO
    BGQKXFKxRjbbRJI3

    • Remove the bobbin from the bobbin case.

    • Remove the screws on the bed cover using the round screwdriver.

    • Place the screwdriver into the groove of the screw. Turn counterclockwise until the screw is loosened.

  5. lo5bZVgWahYckFwp

    • Remove the bed cover to expose the feed dogs.

  6. VjiZHHhASZwffQIU
    VjiZHHhASZwffQIU
    eKqsQhJiKMcnPabo

    • Using the brush and tweezers, clear the area around the feed dogs of lint, thread, and other debris.

    • Be gentle while removing tangled threads to prevent damage to the machine and to reduce the risk of accidentally leaving thread inside the machine.

  7. fwTgv3LkSRwBTYAd
    fwTgv3LkSRwBTYAd
    tgOZal4MwglmJyYl
    wQON3Gp6FaMEFPxL

    • Apply 2 drops of sewing machine oil to the left and right sides of the feed dog.

    • Wipe away excess oil using the microfiber cloth.

  8. iyhEUBrEJHXPOdec

    • Move the feed dogs manually by turning the hand crank clockwise for 3 full rotations in order to disperse the oil evenly.

  9. hKeRI3VWAQgoq1GW

    • Replace the bed cover, bobbin plate, presser foot, and the needle into the machine.

  10. gOOZsMmP6AakYbu1

    • Plug the pedal back into the machine and turn it on.

    • Do a test stitch on scrap fabric to ensure the feed dogs and the machine overall are functioning properly.

Conclusion

To reassemble your device, follow these instructions in reverse order.

1. Switch on and replug the machine

2. Replace the needle

3. Replace the bobbin plate and the presser foot attachment

4. Replace the bobbin and the screws on the bed cover using the round screwdriver.

5. Replace the bed cover.

Author

Khalia Brown

Member since: 02/07/24

181 Reputation

0 comments