Harman Kardon Onyx Studio 2 Bluetooth Antenna Replacement

Written By: Alexandra Achtenberg
  • Comments: 13
Harman Kardon Onyx Studio 2 Bluetooth Antenna Replacement

Difficulty

Moderate

Steps

10

Time Required

20 - 25 minutes

Introduction

After removing the control board and circuit board, the Bluetooth antenna can be accessed and therefore removed. This is helpful if a lack of Bluetooth connectivity is due to the speaker.

  1. dBMtxPy1K1rUnFpu
    dBMtxPy1K1rUnFpu
    iQOTA3V6DRt2d21M
    dQ2kJq1EW24lJYMB

    • Using a plastic opening tool, pry off the front grill by wedging it in the notch on the front of the device.

    Where can I find a new front panel for my speaker

    consomme69 -

    If I take this off can I put it back on

    Burger King -

  2. o5SWK6TwGvJXXZkQ
    o5SWK6TwGvJXXZkQ
    jqcCAC2kkM2JaaRl

    • Remove the five 14.4 mm T10 Torx screws.

    There are NO torxscrews. You have to pull out the rubber grille grips that are inside the screw holes FIRST, then use a regular sized Phillips head screwdriver to remove the cover. No Torxscrewdiver needed. I found this out after I had already purchased one from you guys.

    phillip columbus -

    Mi bocina no tiene los 5 tornillos a la vista,tiene las cavidades ciegas, como lo abro???

    Eduardo Heine -

    Yes there are no Torx screws… you have to remove the rubber grips them the Philip Screws..

    Joe Lim -

  3. aLaClpNCSQVOuCfs

    • Gently pull the front apart from the back.

  4. 1SWuvDl2qU1UaEUc
    1SWuvDl2qU1UaEUc
    yCr1XiiAOCKacJsD

    • Remove the four wires connecting the front and back panels.

    • Pinch the connector tab and pull gently upwards.

    • Repeat for the other three connectors.

    Please can I get a replacement of my panel to the phone

    Chinedu Ogunedo -

  5. MxWnQFehXaDmTplm

    • Pull the silicone button band off of the outer edge of the speaker.

  6. LPmilUqrJAlOHlTy
    LPmilUqrJAlOHlTy
    i3vgKRRIW6feDDuw

    • Disconnect the two pressure connections from the circuit board.

  7. ZEkMh32Usjwbdy5U
    ZEkMh32Usjwbdy5U
    nusK3sFgWBOTkjkG

    • Gently remove the control board band by placing fingers in contact with it through the button openings.

    • Work from the outer edges in so as not to bend the band.

    From where to buy Control panel

    ali -

    From where to buy this control panel

    ali -

  8. mYOLRBFQcPCPT1oE
    mYOLRBFQcPCPT1oE
    gT4EIp3YMS2Q1Bi1

    • Disconnect the remaining connectors from the circuit board.

    • Disconnect the Bluetooth antenna.

  9. 6KYrct1kDkhK5dWw
    6KYrct1kDkhK5dWw
    QcCIKnfkO4dULMNm

    • Remove the four 10 mm T10 Torx screws.

    • Pull the circuit board out of the device as it is now free.

    Bisa di kirim

    Mala Ganni -

    Bisa pesan 1

    Mala Ganni -

    I own two of these and the both shut down on their own.. where do I buy the replacement boards from?

    Darren Vincent -

  10. DNE5RvFPSgwkxwvY
    DNE5RvFPSgwkxwvY
    jEcqNGY3422X4sNF

    • Using the wide blue plastic opening tool, gently peel back edges of the Bluetooth board.

    • Peel off completely and remove from the device.

    I was wondering if you guys have this bluetooth antenna available for sale.

    Thank you

    Julio Dávila -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Alexandra Achtenberg

Member since: 02/02/17

2051 Reputation

One comment

Any idea where we can purchase the replacement parts?

Cort Krause -