HP Photosmart c3180 Scanner Bulb Replacement

Written By: Jim
  • Comments: 3
HP Photosmart c3180 Scanner Bulb Replacement

Difficulty

Moderate

Steps

12

Time Required

10 - 15 minutes

Introduction

If the scanner on your HP Photosmart c3180 is not working, you may want to check the scanner bulb.

The scanner bulb illuminates the document being scanned in order for the printer to get a clearer image of the document.

Scanner bulbs dim over time and eventually burn out. This requires the owner to replace the bulb in order to get the scanner working again.

This guide requires steady hands to deal with small parts as well as knowing the parts of the printer.

BEFORE REPLACING BULB UNPLUG PRINTER FROM POWER SOURCE

  1. OKnwwk4wKnmRT1TC
    OKnwwk4wKnmRT1TC
    4mMrqMtB2SbxGwDb

    • Before disassembling your printer, be sure that the printer has been unplugged to avoid any risk of injury.

    • Rotate the printer 90 degrees counter clockwise so that the side panel next to control panel is facing you.

    • Remove the two T10 12mm Torx screws from the left side panel.

  2. 6tGoCT5KMFM5Tujb
    6tGoCT5KMFM5Tujb
    sol1ObLCA3Fi5bCP

    • Firmly pull the the back of the side panel until it separates from the body of the printer.

    • Rotate the side panel upwards while pulling it towards yourself to remove the panel.

  3. CJLV3tKkxatgK3C6
    CJLV3tKkxatgK3C6
    VUrdBBDEuq3CDUmO

    • Rotate the printer 90 degrees clockwise.

    • Grasp the paper tray and rotate it down.

    • Insert your fingers into the slot in the printer door and pull to rotate the gate down.

  4. MQNKnT1dnoAeoGPb
    MQNKnT1dnoAeoGPb
    oeKScQC6qWbRxPgM

    • Rotate the printer 90 degrees clockwise.

    • Remove the two T10 12 mm Torx screws.

    • Grasp both sides of the side panel and pull it forward to remove the panel.

  5. lwpt6KWNfsIpZUtp
    lwpt6KWNfsIpZUtp
    ZfvKNRS54AeP1RaT

    • Rotate the printer 90 degrees counter clockwise.

    • Lift the scanner lid to expose the scanner glass.

  6. UATXBmLKNIQvWHWj

    • Remove the two T10 12 mm Torx screws.

    • Do not attempt to lift the top panel off the printer yet because it is still connected to the printer body by a cable.

  7. MCf1iKQovxZeKoOs
    MCf1iKQovxZeKoOs
    tRdaT6fmasSfwWJE

    • Rotate the printer 90 degrees counter clockwise.

    • Inside the printer is a small white tab. Press it inward with a spudger until a pop is heard.

    • Remove the front panel by grasping its front and pulling away from the printer.

    Änderung des Textes: die kleine Lasche verriegelt die kleine Frontblende: mit leichtem Druck Richtung “rechte Druckerseite entriegeln, gleichzeitig jene Blende nach vorn lösen.

    Garofalo -

  8. b4wmJyCQ4dGIfRQm
    b4wmJyCQ4dGIfRQm
    noxLPZnY6FFCoqRa

    • Rotate the printer 90 degrees clockwise.

    • Remove the cable connecting the top panel of the printer to the power button assembly.

  9. I5PMnusHEehpT52Y

    • Carefully lift the top panel of the printer away from the printer body.

    nur die dünne weiße Abdeckung, die graue bleibt noch; zuerst hinten anheben, vorn ist mittig eine Nase zu lösen.

    Garofalo -

  10. DqUU4RdD1YjqeXV2
    DqUU4RdD1YjqeXV2
    Ngvsa2ULUUT2xILI

    • Set aside the top panel of the printer.

    • Lift the scanner carriage vertically, being careful not to yank of the cables connecting it to the printer.

  11. yRFECMNa4qtcDLoO
    yRFECMNa4qtcDLoO
    RyLrUeVfjluoAIDb

    • Flip the scanner carriage over to expose the connectors on the bottom.

    • Carefully remove the small cable from the connector.

    • Carefully remove the large cable from the connector.

  12. fobR4WQYVdDj6JY4
    fobR4WQYVdDj6JY4
    MUTGBUVtRd2I2JXV

    • Remove the scanner carriage from the scanner tray and flip it upside down.

    • Remove the two T10 12mm Torx screws.

    • Remove the scanner carriage from the scanner bulb.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jim

Member since: 06/10/11

1608 Reputation

One comment

You say no parts needed to be purchased. You have to buy a new scanner bulb if you’re replacing it.

ddaviddierlam -