HP Photosmart Premium C309g TouchSmart Display Screen Replacement

Written By: Laura
  • Comments: 1
HP Photosmart Premium C309g TouchSmart Display Screen Replacement

Difficulty

Easy

Steps

13

Time Required

15 - 20 minutes

Introduction

Replace the TouchSmart display screen on the front of the printer. This screen serves as the main menu and control of all the machine's functions. If the screen becomes unresponsive or physically damaged, it may need to be replaced.

  1. AJITWLcdu5SY5Uqs

    • Open the top of printer. The printer should appear as shown.

  2. RIi3KK2IduwInuDu
    RIi3KK2IduwInuDu
    SVcTh3GKEYVVqBNE

    • Use the blue plastic opening tool to pry the trim pieces all the way around the printer.

    • Loosen the pieces around the edges before pulling to remove from the printer.

    • Pull the (4) trim pieces off and set them aside.

  3. FMThcISZolBRBwXH
    FMThcISZolBRBwXH
    3IsxxEtQ4fcklBxA

    • Using the blue plastic opening tool, pull from the middle and then slide back to remove the side panels.

    • The side trim pieces need to be removed before the front trim pieces.

  4. BBZYRBm6WMVS5SiI

    • Using the T9 Torx Security screwdriver bit, unscrew the five 12mm screws shown.

  5. EUZP3CQfbHRuZlaS

    • The scanner flap is attached by a clip that can be dislodged by pulling it gently away from the printer.

    • Keeping the scanner flap upright, slide it toward the unattached clip in order to dislodge the second clip.

    • Both clips will come unattached and you can set the scanner flap aside.

  6. uFlDUuiNjHqSkpWS
    uFlDUuiNjHqSkpWS
    XqIpGWoYWqh1o3jf

    • Lift the scanner glass piece from the printer and set it aside.

  7. lcrWvtGYQFKIM2AS

    • Gently pull the display screen away from the printer.

    • Locate & unscrew the two 12mm screws using the T9 Torx Security screwdriver bit.

  8. VfIxb6UMVA2T5bQP
    VfIxb6UMVA2T5bQP
    dEEbhvFZcfx3g6Fq

    • Place thumb and forefinger where shown and pull this piece away from the printer.

    • Do not pull it away too hard. The piece is still connected by wiring ribbon.

  9. tyx3AAtaMOE5ihOx
    tyx3AAtaMOE5ihOx
    ckpdXUFIPv6sjSrU

    • Pull both wiring ribbons out from the display screen piece. This will separate the piece from the printer.

    • Use tweezers if necessary.

  10. nA6DKrCIyBaXuplB
    nA6DKrCIyBaXuplB
    fnRi2EBF2BIviZBE

    • Push forward and down to release the retaining piece. This will detach the display screen from the front panel.

  11. uZxulcjM1SpY5JMl

    • Set the display screen face down.

    • Locate and unscrew all four 12mm screws on the back on the display screen using the T9 Torx Security screwdriver bit.

  12. eGPYx34PH3lSpISS

    • Lift the back of the display screen to remove it.

  13. WXOLTS1RPH2ZBVDM
    WXOLTS1RPH2ZBVDM
    rJniZT1NChXYYTYg

    • Place hands as shown and push with your thumbs to detach the plastic from the screen.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Laura

Member since: 23/10/14

694 Reputation

One comment

where can i get replacement part

fernando -