Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement

Written By: Larry Huang
  • Comments: 4
Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement

Difficulty

Moderate

Steps

22

Time Required

15 - 30 minutes

Introduction

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

  1. lccTL6SZ3kbvrUG2

    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

  2. QYteIeiAr3eYANHf
    QYteIeiAr3eYANHf
    YacUSN6hThuTEpFy

    • Locate the IEEE cover in the back.

    • Gently slide the cover to the right to unlatch, then pull to remove it.

    errore avevo chiesto informazioni x sostituire la batteria al cellulare HUAWEI Mod. LX1

    Luigi Martinenghi -

    avevo chiesto informazioni x la sostituzione della batteria cellulare HUAWEI Mod.LX1

    Luigi Martinenghi -

  3. C4dBWDDOARfU6BKl
    C4dBWDDOARfU6BKl
    Zobe3GQ4ytZXQuXj

    • Using a Phillips #2 screwdriver, remove the four 10 mm screws shown.

    • Remove the 6 mm screw that holds the rear housing in place.

  4. iSFOcWcCsIxvdqON
    iSFOcWcCsIxvdqON
    BfSTmc334IPJEjIW

    • Remove the rear housing by pulling it backwards.

  5. ZRQjtn2Y1AjXrlTx
    ZRQjtn2Y1AjXrlTx
    VS6Om6BsNLdA6RX1
    q1rUDpQs4M13aSXO

    • Insert a plastic opening tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion.

    • Remove the side housing by pulling it outwards.

  6. vfiVSPXdkGxi1FFa
    vfiVSPXdkGxi1FFa
    fEIKc1TbHiBORjdF

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

  7. JyXjekvUHEsuITOZ
    JyXjekvUHEsuITOZ
    GHYP2VbWwuIIexap
    Twc3ylCxi3RZdNAd

    • Lift the paper support.

    • Open the printer cover and front cover.

  8. XgpHaunnOSVioafK
    XgpHaunnOSVioafK
    xxXUiIkZyPRmwsnn
    uD12N4KNMu1DRYHI

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6 mm Phillips #2 screws.

  9. iTMoHjNDg4EXjWr6
    iTMoHjNDg4EXjWr6
    auVkiwhoUQ5t3yOR

    • Detach the tabs from the pins on each side by pulling it outwards.

  10. tCKNoqZRVGbrTnYR
    tCKNoqZRVGbrTnYR
    5CcLsgUa3gDWxdMl

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

  11. ShQrsIGl1fSNefvJ
    ShQrsIGl1fSNefvJ
    2IXjV2g466oM1Ryu
    RTWbClacrIBJ6yJD

    • Disconnect the two cables on the side by carefully pulling it outwards.

    • You may need to gently rock the two cables up and down while pulling.

  12. GNbFiqQLlN4SnJv5
    GNbFiqQLlN4SnJv5
    4NKVJbuNDxa5hqHg

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

    this is where I get stuck. the top won't come off. it seems to be stuck at the right front corner, where the buttons are. Is the button grouping part of the upper housing or does it come separate from the upper housing unit. The picture appears that you are taking the button attachment as part of the upper housing unit. But it is really stuck there on my 1400.

    1gr8nana -

  13. AojbhBP6VJdWmbsw
    AojbhBP6VJdWmbsw
    be1XuUvkahkXBP3A

    • Start by emptying the ink tube.

    • Hold the left side of the ink tube in your hand.

    • Pull the sides of the tube apart and empty the waste.

  14. ueNTskJUYVj4XFSC
    ueNTskJUYVj4XFSC
    gcJOl1UZsOWuQgq5

    • Remove the acetate tape that secures the connector cable.

  15. ACaNJ4E2AETqEfqe
    ACaNJ4E2AETqEfqe
    aQNvDYlOOvpQXVyN
    oZr2DPbX2pkHi4Vs

    • There are six screws that secure the printer mechanism.

    • Remove the first three 10 mm screws that hold the printer mechanism in place using a Phillips #2 screwdriver.

  16. BLJokjjpQsBPHRSU
    BLJokjjpQsBPHRSU
    iHVvHapfZOj43rOu
    2GN5HAQUn2XYJhXV

    • Remove the other three 10 mm screws that secure the printer mechanism using a Phillips #2 screwdriver.

  17. NoVIidJOpXF2ZirD
    NoVIidJOpXF2ZirD
    aGr2cTvUgWGy5lFW

    • The printer mechanism is located on the lower housing.

    • Remove the mechanism by holding the handles and lifting upwards.

  18. 5v1WgC6Wil3En2kE
    5v1WgC6Wil3En2kE
    LtfTQMR21dVNkS4H
    Z4jwYoBnGJCOaOiy

    • Remove the CD-R unit housing. Release the two attaching points to the tray base and then pull out the unit diagonally one side at a time.

  19. VeKkvNaHggM1qUll
    VeKkvNaHggM1qUll
    6hcmyocQweMtwAk6
    OOk5WxRbFCSIBlOq

    • Detach the left frame support plate. Start by removing the two 6 mm screws that secure it and then pull it out by hand.

  20. ZqJs3FMj1HVdIMQQ
    ZqJs3FMj1HVdIMQQ
    VZTuTRNVkKbGkLos

    • Remove the four 6 mm screws using the Phillips #2 screwdriver.

    • Remove the two 8 mm screw using a Phillips #2 screwdriver.

    • The screws are located on the lower sections of the printer.

  21. oFh4kN2BwTQCceBK
    oFh4kN2BwTQCceBK
    fFaAsay5dqK2BxyV
    Kr3xW3HeaQZttJMS

    • Two guide pins secure the paper eject assembly in place.

    • Pull out the two guide pins on the CD/DVD tray base.

    “Pull out the two guide pins on the CD/DVD tray base”?

    What are you talking about? What CD/DVD tray? THIS IS A PRINTER!!!

    pettersen -

  22. utgHeeUJ5x4SSoOV
    utgHeeUJ5x4SSoOV
    QM1iHQxTxMkyoY4C

    • Remove the paper eject frame assembly by pulling it towards you.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Larry Huang

Member since: 12/10/11

1004 Reputation

0 comments