Disassembling Sony Cyber Shot WX80 Total Disassembling Part by Part

Written By: Scott Grambo
  • Comments: 7
Disassembling Sony Cyber Shot WX80 Total Disassembling Part by Part

Difficulty

Moderate

Steps

7

Time Required

35 - 50 minutes

Introduction

Use this guide to fully disassemble a Sony Cyber-Shot WX80, a compact digital camera first released in 2013 and since discontinued. Please note: This guide is intended to provide instructions on disassembling the Sony Cyber-Shot WX80 and does not provide guidance for repairing or replacing individual parts of the camera.

If you are experiencing issues with your Sony Cyber-Shoot WX80, a troubleshooting guide can be found here. A motherboard replacement guide can be found here, and you can find more guides on our website.

Before beginning, ensure the device is not attached to any external power sources and power it down completely.

  1. KdO2SbnOreBLCPiG
    KdO2SbnOreBLCPiG
    lPPUCVHufDWNVZDA
    EcoN4T4DVXatju5y

    • Remove all six #00 screws holding the outer chassis together with a Phillips #00 screwdriver.

    • Keep track of all screws as they are small and very easy to lose

  2. hFuxWIDTufWBsO6s
    hFuxWIDTufWBsO6s
    sGUb2FaL2nXQjLuF
    ANfAKO4bCJXGcQVa

    • At this point most of the parts in the camera should be free moving.

    • Take note of the small free moving flap near the battery port seen in the first of the three photos.

    • Remove the front of the shell case with the spudger. Insert the spudger into the seam on the right side of the camera and pry away from the back case.

    • Using the spudger, repeat the process to remove the back of the case. Pry away from the front of the camera.

  3. 2iaQPEOCyAKU1GIr
    2iaQPEOCyAKU1GIr
    OVQL4Y21UmOyMiZl
    Zoc3IE4G5UlhS4HR

    • Turn the camera so that you are looking at the LCD screen.

    • Use tweezers to remove the first of two ribbon cables holding the LCD screen in place. Pull directly out of the port.

    • Use tweezers to remove the second of the two ribbon cables using the same method.

    • Take care not to tear the ribbons. They are the communication networks that your screen uses to operate.

    • The LCD screen is now detached. Gently pull it apart from the rest of the camera with your hands.

    There’s an extra small part with some metal on it. But i cannot figure out where it came from?

    Brayan -

  4. xDCDGkEi5KgSMq2A
    xDCDGkEi5KgSMq2A
    dT4xnEDIXPVKdOTw
    A41hMDF5eSKIFGJg

    • Turn the side of the camera you just removed the cable ribbons from toward you.

    • The inner lining frame has an orange ribbon cable (circled in the image) that needs to be detached before it can be safely removed.

    • Remove the inner frame lining with tweezers.

    • Do so gently to avoid damaging the ribbon cable.

    • Carefully lift the inner frame lining away from the rest of the camera with your fingers.

    There’s a really small price I cannot figure out where it came from? Can anyone help?

    Brayan -

  5. qyLOfLy2qc6LVuAE
    qyLOfLy2qc6LVuAE
    lYIx3COvsJekGjUu

    • With the LCD screen removed, you should see a black metal plate. This can be pulled off to reveal the motherboard and the lens.

    • Use your fingers to gently lift the plate up and away from the rest of the camera.

  6. ONgIwRka4wTIYWfh
    ONgIwRka4wTIYWfh
    hLiMIRLE5nNPbnRd

    • You should now be able to see the exposed motherboard and lens.

    • To separate the motherboard and lens, you must detach two more ribbon cables.

    • Remove the first ribbon cable (pictured first) with tweezers. Pull gently away from the camera.

    • Remove the second ribbon cable (pictured second) with tweezers. Pull gently away from the camera.

    • Use your fingers to gently lift the lens away from the motherboard and frame.

  7. qysqKCypvOlrGPFG
    qysqKCypvOlrGPFG
    H1twWgrTwNiW4vEk

    • Remove the screw (pictured first) with the #00 Phillips screwdriver.

    • Use tweezers to remove the last ribbon cable (pictured second). Pull gently away from the camera frame.

    • You should now be able to remove the motherboard from the base skeleton frame.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Scott Grambo

Member since: 08/04/15

264 Reputation

5 comments

So what about the other parts not in your photos that fall ?

The bracket around the speaker and this little white part that fell out as soon as I lifted the back cover a little? can you please give more info

Kat -

I'm also finding where was the white parts located. It seems that without this part, wx80 works well. If you found its location, please give me hint. Thanks.

Chung-Suh Ku -

Maybe this helps for the location of the white part: https://www.quora.com/What-does-the-insi...

Christian Urban -

This is not complete disassembly pics. Not at all. This is half the steps.

Mayur Panghaal -

Huh?

How about the sensor? How do I clean the sensor?

jim dandy -