Introduction
-
-
1. Drill a hole in the top right corner 16.5 mm from the top and 30.3 mm from the side using a 13/16 inch drill bit.
-
2. Drill two holes in the side 30 mm from the short sides and 27 mm from the long side using a 1/2 inch drill bit.
-
3. Screw in two waterproof cable gland connectors to the side holes.
-
Put in a button in the rocker switch in the other hole.
-
-
-
4. Cut the purple wire and the inline fuse holder wire 10 inches long.
-
5. Attach a 10A, 12VDC fuse.
-
-
-
6. Strip both wires about 1/2 inch
-
7. using the 16 gauge slot of the wire stripper
-
8. Get 3 pink and 3 blue fully insulated heat-shrink quick-disconnect terminals.
-
-
-
9. Crimp the fully insulated heat-shrink quick-disconnect terminal onto the end of the wire.
-
10. Use the heat shrink gun to heat shrink the ends of the crimps.
-
11. Repeat for both ends of both wires.
-
-
-
12. Cut two feet of red and black 16G wire (grey insulated wire) and then strip 2 inches off of the grey insulation.
-
13. Strip 1/2 inch of both the black and red wires.
-
-
-
14. Place two metal contacts on both the red and black wires.
-
15. Crimp the contacts into place.
-
16. Thread the contacts into the Amphenol connector.
-
-
-
17. Attach the green wedge to the connector.
-
18. Cut 1.5 inches of 2:1 0.25" diameter heat shrink tubing.
-
19. Use the heat shrink gun to shrink the heat shrink tubing.
-
-
-
21. Cut 30 inches of red and black 16G wire (grey insulated wire). Strip 2 inches of the grey rubber coating from both ends.
-
22. Strip 0.5 inches from both the red and black wires from both ends.
-
23. Obtain a 2-pin amphenol connector.
-
-
-
24. Disconnect the 2-pin amphenol connector into its individual parts.
-
25. Loosen the screws on the amphenol connector. Thread the stripped wire through the end of the amphenol connector and through the middle piece of the amphenol connector.
-
26. Solder the wires to the other end of the amphenol connector.
-
-
-
27. Obtain a Flux Remover Pen, 99 % Isopropyl Alcohol, and a Q-Tip.
-
28. Use the pen to remove the flux from the soldered pins.
-
29. Dip the q-tip in the alcohol. Use the q-tip to remove the flux remover.
-
-
-
30. Screw the amphenol pieces back together. Then tighten the external screws.
-
31. This is what a final 2-pin amphenol connector looks like.
-
32. Thread the 2-pin amphenol autosampler wire through the top hole and the battery connector wire through the bottom hole of the enclosure box. Leave about a foot of each on the outside of the box. Tighten the glands.
-
-
-
Once 2 pin and battery wires constructed and threaded into box, strip opposite ends and add heat-shrinking quick disconnect terminals.
-
-
-
33. This is what the wires look like threaded through the glands in the box.
-
34. Connect the battery wire to the first two prongs of the rocker switch.
-
35. Connect the 2-pin amphenol autosampler wire to the last two prongs of the rocker switch.
-
-
-
36. Connect the purple wire and fuse wire to the middle two prongs of the rocker switch.
-
37. Connect the other side of the purple wire and fuse wire to a 12 volt battery.
-
-
-
39. Place the 12V battery and all the wires into the enclosure.
-
40. Screw the lid onto the enclosure.
-
41. This is what the completed battery enclosure looks like.
-
